Dell EMC PowerEdge R7525 Скачать руководство пользователя страница 149

Страница: 149 / 209

Figure 108. Installing the IDSDM module

Next steps

Install the MicroSD cards

NOTE:

Reinstall the Micro-SD cards into the same slots based on the labels you had marked on the cards during

removal.

2. Follow the procedure listed in

After working inside your system

on page 47.

MicroSD card

Removing the MicroSD card

Prerequisites

1. Follow the safety guidelines listed in the

Safety instructions

on page 46.

2. Follow the procedure listed in the

Before working inside your system

on page 47.

Remove the IDSDM module

Steps

1. Locate the MicroSD card slot on the IDSDM module, and press the card to partially release it from the slot. For more information about

the slot location, see

System board jumpers and connectors

section.

2. Hold the MicroSD card, and remove it from the slot.

NOTE:

Temporarily label each MicroSD card with the corresponding slot number after removal.

Installing and removing system components

149

Содержание PowerEdge R7525


















































































































































































































Результаты поиска

Содержание PowerEdge R7525

Отзывы:

Dell EMC PowerEdge R7525, Инструкция по установке и обслуживанию, Страница: 149 / 209

Результаты поиска

Содержание PowerEdge R7525

Отзывы: