Dell EMC ES40 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 66

background image

Installing a new or replacement disk

Before you begin

Use ESD gloves or attach an ESD wristband to your wrist and the enclosure in which you are
installing the disk.

About this task

on page 34 while performing the procedure that follows.

NOTICE

If you are installing multiple disks in a storage system that is powered up, wait at least

10 seconds before sliding the next disk module into position.

Procedure

1. Align the disk with the guides in the slot.

2. With the disk latch fully open, gently push the disk into the slot.

The disk latch begins to rotate downward when its tabs meet the enclosure.

3. The disk latch begins to rotate downward when its tabs meet the enclosure.

4. After the latch is engaged, push firmly on the bottom of the disk to verify that the disk is

properly seated.

Figure 22 Installing a disk

1

2

Tabs

CL4645

4

3

The disk's active light flashes to reflect the disk’s spin-up sequence.

After you finish

Remove and store the ESD gear.

Removing and replacing FRUs

34

Dell EMC ES40 Expansion Shelf Guide Field Replacement Unit Guide

«
...
32
33
34
35
36
...
»

Содержание ES40



































































Отзывы:

Нет отзывов

Похожие инструкции для ES40

Бренд: Palace Imports Страницы: 6

Бренд: Balt Страницы: 6

Бренд: Balt Страницы: 4

Бренд: velda Страницы: 24

Бренд: Safco Страницы: 7

Бренд: Safco Страницы: 6

Бренд: Safco Страницы: 2

Бренд: Safco Страницы: 5

Бренд: Safco Страницы: 3

Rocklin PAT7007

Бренд: Safavieh Страницы: 6

Бренд: Safavieh Страницы: 3

Бренд: OLG Страницы: 6

Бренд: Urban Barn Страницы: 2

PERCH NEST 1PNB01

Бренд: Oeuf Страницы: 22

ROGER BISTROT WOOD

Бренд: Cattelan Italia Страницы: 2

Бренд: HAMPTON BAY Страницы: 13

ALFRED 2RR 67807

Бренд: Amart Furniture Страницы: 5

ESSENCE 157-101

Бренд: Blanco Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды