background image

3

HARD DRIVE INSTALLATION (BB MODELS ONLY)

• 

Disconnect the power supply.

• 

Remove the screw in the top centre of the rear panel and the screw on each side 

of the unit and remove the top casing.

• 

With reference to the four keyhole slots in the base of the unit, partly insert a 

suitable screw into the relevant threaded mounting points on the hard drive.

• 

Connect the power and data cables to the hard drive then locate the mounting 

screws into the keyhole slots, slide sideways then from underneath, tighten them 

to fix the drive into place.

• 

Route the cables neatly ensuring all the connectors are fully pushed home.

• 

Refit the top casing and replace the three screws.

Note: 

only use hard drives recommended by the manufacturer for continuous DVR 

usage.

• 

Connect the cameras to the video input sockets.

• 

Connect a monitor to either the VGA/HDMI output sockets as required.

• 

Connect the mouse to a USB socket.

• 

Connect the power supply to the DC socket and plug into a mains socket and turn 

the power on. The red LED on the front panel will light.

• 

The DVR will display the boot screen followed by the log on window.

• 

Default username is ‘admin’ and password is ‘12345’.

• 

After successful log on you can set the general configuration of the unit including 

modifying the username and password, language, video standard and the time.

• 

Click ‘Next’ to set further parameters as follows:

Note: If you have previously configured all parameters the set up wizard can be 

bypassed on future booting by un-ticking the option box on the boot screen. You 

can also turn off the boot wizard in Settings/General.

Drive Mountings

LOGGING ON

5.3 Network Settings

5.4 Channel Configuration

6.1 Login

6.WEB Operation

6

5.5 IP Channel Configuration

5.6 Recording Settings

8.Disclaimer

8

7.Mobile App Operation

7

5.7 Instant playback

5

1. As a result of the following reasons, if the product interrupts or 

terminates the service for any of the following reasons, the company 
shall not be liable for personal injury or property damage to you or a 
third party. Failure to install or use properly as required; for the sake of 
national or public interest; force majeure; your own or third-party 
reasons (including but not limited to the use of third-party products, 

software or components, etc.

2. The company has not expressed or implied that this product is 
applicable to special purpose.This product may not be used in medical 
/ safety equipment or other applications where there is a breakdown of 
the product that could result in life-threatening or personal injury, as 
well as hazardous or non-humanitarian hazards such as weapons of 
mass destruction, biological and chemical weapons, nuclear explosions 
or any unsafe use of nuclear energy use. Any loss or liability arising out 
of the above use will be at your own risk.
3. This product, when properly installed and used, can detect 
unauthorized intrusion during a particular delight but can not avoid 
accidents or personal injury or property damage. In your daily life, you 
should be vigilant and strengthen your safety awareness.
4. The Company is not responsible for any indirect, incidental, special 
punitive damages, claims, loss of property or loss of any data or 
documents. To the maximum extent permitted by law, the liability for 
compensation of company is not exceed than the amount you paid for 

this product.

The following exemptions or limitations of liability, please pay 

special attention to:

XVR LAN login(the PC and the device are in the same router)
Step 1: Make sure the XVR and PC are in same network segment. If not, 

the network segment of PC need to be set up to the same segment with 
XVR, such as "192.168.1.99".
Step 2: Open IE browser, select Tools > Internet Options > Security > 
Custom Level > ActiveX controls and plug-ins, all options are enabled.
Step 3: Open "Search Tool", double-click the target device from the 
search result to enter the login interface, or open the IE browser to enter 
the XVR address: such as “http://192.168.1.88/ “(If the http port of the XVR 
is changed to 89, enter "http:// 192.168.1.88:89/”) to enter the login 

interface.

Step 4: Enter the device user name (default is “admin”), password (default 
is “12345”), and click “Login”.

In the preview interface, click the play button at the bottom. For the first 
time connecting, you have to download and install the plugin before 

previewing. 
NOTE: 

The Web-side can also perform the operations such as system, network, 
storage, playback, download, upgrade, maintenance, and factory reset 
on the Web.

6.2 Preview

Step 1: Choose "Menu> Playback" or right click on the preview interface 
and select "Playback" to enter the Playback interface.
Step 2: Choose "Date > Channel > More". Double click to search for the 
file, and the interface will start playing the file. Or select the "time > 
channel", left mouse click on the time progress bar below the playback 
interface to play the video.

Choose "Menu> Shut Down", click "Shut Down".

5.8 Playback

5.9 Shut down

Step 1: When the mouse clicks anywhere in the current channel screen, 
the control bar will automatically pop up below the channel.
Step2: Click ”      ” to enter the instant playback interface, can play the first 

5 minutes of the current channel video.

NOTE:

1. If you do not need to set the device, you can click "Cancel" to exit the 
boot wizard interface. You can also turn off the boot wizard in " Menu > 
Configuration> General ".
2. You should reset the device administrator password (the system default 
username is "admin" and the password is "12345") when booting for the 
first time. To ensure the security of the device, please save the admin login 
password and modify it regularly.

Step 1: Choose “Menu> Configuration> Channel Config”.
Step 2: Select the signal access type of each channel as required.
Step 3: Click “Apply>Confirm”, the device restarts and the modified 

Channel configuration takes effect.

Network parameters must be properly configured before operating the 

device over the network.

Procedure: Choose “Menu > Configuration > Network”. The system displays 
the IP/Port interface. Modify the IP address of the device according to the 
actual network plan. (The default IP address of the XVR is 192.168.1.88.).

NOTE:
1. Single channel select signal access mode to follow certain rules, the 

interface will be automatically reflected in the optional options.
2. The actual access signal should be checked with the signal mode. If a 
channel selected "HD" mode, you can access the 

TVI / CVBS / AHD / CVI

 

signal; when switching signals cause abnormal display, you can reconnect 
the video cable; if a channel is selected "IP" mode, is the IP channel , Can 

access IP equipment.
3. In the preview interface, when the HD (TVI / CVBS / AHD / CVI) channel 

has no image source, the channel displays “HD VIDEO”; when there is no 
signal source in the IP channel, the channel displays “NO CONFIG”. When 
there is no image source, the channel displays “NO VIDEO”.

Before accessing and configuring the IP channel, make sure that the XVR 
network connection is correct and valid.

Step 1: Choose "Menu> Camera> Add Camera" to enter the Add Camera 

interface.

Step 2: Add IPC by automatically or manually. 
    Automatically add, click "Auto add" button.
    Manually add a device, click "Add", the Device Search interface 
automatically searches for "Onvif" or "Private" protocol (if our company IPC 
recommends selecting "Private"), select the IP device to be added, and 

click "Add", select add channel, click "Save" to complete the addition.

NOTE:

The device opens all channels by default for 24 hours record. 

Step 1: Choose "Menu> Record > Schedule" to enter the Schedule 

interface.

Step 2: Select the channel and recording type according to the actual 
needs. Hold down the left mouse button and drag the mouse in the time 
period diagram or click “          ” to set the recording schedule.

Step 1: Download and Install

Use the Android or iOS phone to scan the corresponding QR code or 
search "BitVision" from the application store to download and install 
the BitVision App.

Android App QR

iOS App QR

Step 2: Account login

Run BitVision App, click "        " in the sliding sidebar, enter the account 
name and password, and click “Login” (Note: no account is required to 

register first).

Step 3: Add device

After login, click "Device manage" ,  "       " and "        Add device" , 
select "SN Add", enter the device user name, password and verification 
code after scan the QR code (the verification code printed on the 

label), click "Submit" to set device name and group, click "Finish" and 

the addition is successful.

Step 4: Live preview

Select "Real time" and "           " to enter the device list in the main 

interface, select the device channel to be previewed in the group, you 

will see the live video after click " Done ".

5

5.3 Network Settings

5.4 Channel Configuration

6.1 Login

6.WEB Operation

6

5.5 IP Channel Configuration

5.6 Recording Settings

8.Disclaimer

8

7.Mobile App Operation

7

5.7 Instant playback

5

1. As a result of the following reasons, if the product interrupts or 

terminates the service for any of the following reasons, the company 
shall not be liable for personal injury or property damage to you or a 
third party. Failure to install or use properly as required; for the sake of 
national or public interest; force majeure; your own or third-party 
reasons (including but not limited to the use of third-party products, 

software or components, etc.

2. The company has not expressed or implied that this product is 
applicable to special purpose.This product may not be used in medical 
/ safety equipment or other applications where there is a breakdown of 
the product that could result in life-threatening or personal injury, as 
well as hazardous or non-humanitarian hazards such as weapons of 
mass destruction, biological and chemical weapons, nuclear explosions 
or any unsafe use of nuclear energy use. Any loss or liability arising out 
of the above use will be at your own risk.
3. This product, when properly installed and used, can detect 
unauthorized intrusion during a particular delight but can not avoid 
accidents or personal injury or property damage. In your daily life, you 
should be vigilant and strengthen your safety awareness.
4. The Company is not responsible for any indirect, incidental, special 
punitive damages, claims, loss of property or loss of any data or 
documents. To the maximum extent permitted by law, the liability for 
compensation of company is not exceed than the amount you paid for 

this product.

The following exemptions or limitations of liability, please pay 

special attention to:

XVR LAN login(the PC and the device are in the same router)
Step 1: Make sure the XVR and PC are in same network segment. If not, 

the network segment of PC need to be set up to the same segment with 
XVR, such as "192.168.1.99".
Step 2: Open IE browser, select Tools > Internet Options > Security > 
Custom Level > ActiveX controls and plug-ins, all options are enabled.
Step 3: Open "Search Tool", double-click the target device from the 
search result to enter the login interface, or open the IE browser to enter 
the XVR address: such as “http://192.168.1.88/ “(If the http port of the XVR 
is changed to 89, enter "http:// 192.168.1.88:89/”) to enter the login 

interface.

Step 4: Enter the device user name (default is “admin”), password (default 
is “12345”), and click “Login”.

In the preview interface, click the play button at the bottom. For the first 
time connecting, you have to download and install the plugin before 

previewing. 
NOTE: 

The Web-side can also perform the operations such as system, network, 
storage, playback, download, upgrade, maintenance, and factory reset 
on the Web.

6.2 Preview

Step 1: Choose "Menu> Playback" or right click on the preview interface 
and select "Playback" to enter the Playback interface.
Step 2: Choose "Date > Channel > More". Double click to search for the 
file, and the interface will start playing the file. Or select the "time > 
channel", left mouse click on the time progress bar below the playback 
interface to play the video.

Choose "Menu> Shut Down", click "Shut Down".

5.8 Playback

5.9 Shut down

Step 1: When the mouse clicks anywhere in the current channel screen, 
the control bar will automatically pop up below the channel.
Step2: Click ”      ” to enter the instant playback interface, can play the first 

5 minutes of the current channel video.

NOTE:

1. If you do not need to set the device, you can click "Cancel" to exit the 
boot wizard interface. You can also turn off the boot wizard in " Menu > 
Configuration> General ".
2. You should reset the device administrator password (the system default 
username is "admin" and the password is "12345") when booting for the 
first time. To ensure the security of the device, please save the admin login 
password and modify it regularly.

Step 1: Choose “Menu> Configuration> Channel Config”.
Step 2: Select the signal access type of each channel as required.
Step 3: Click “Apply>Confirm”, the device restarts and the modified 

Channel configuration takes effect.

Network parameters must be properly configured before operating the 

device over the network.

Procedure: Choose “Menu > Configuration > Network”. The system displays 
the IP/Port interface. Modify the IP address of the device according to the 
actual network plan. (The default IP address of the XVR is 192.168.1.88.).

NOTE:
1. Single channel select signal access mode to follow certain rules, the 

interface will be automatically reflected in the optional options.
2. The actual access signal should be checked with the signal mode. If a 
channel selected "HD" mode, you can access the 

TVI / CVBS / AHD / CVI

 

signal; when switching signals cause abnormal display, you can reconnect 
the video cable; if a channel is selected "IP" mode, is the IP channel , Can 

access IP equipment.
3. In the preview interface, when the HD (TVI / CVBS / AHD / CVI) channel 

has no image source, the channel displays “HD VIDEO”; when there is no 
signal source in the IP channel, the channel displays “NO CONFIG”. When 
there is no image source, the channel displays “NO VIDEO”.

Before accessing and configuring the IP channel, make sure that the XVR 
network connection is correct and valid.

Step 1: Choose "Menu> Camera> Add Camera" to enter the Add Camera 

interface.

Step 2: Add IPC by automatically or manually. 
    Automatically add, click "Auto add" button.
    Manually add a device, click "Add", the Device Search interface 
automatically searches for "Onvif" or "Private" protocol (if our company IPC 
recommends selecting "Private"), select the IP device to be added, and 

click "Add", select add channel, click "Save" to complete the addition.

NOTE:

The device opens all channels by default for 24 hours record. 

Step 1: Choose "Menu> Record > Schedule" to enter the Schedule 

interface.

Step 2: Select the channel and recording type according to the actual 
needs. Hold down the left mouse button and drag the mouse in the time 
period diagram or click “          ” to set the recording schedule.

Step 1: Download and Install

Use the Android or iOS phone to scan the corresponding QR code or 
search "BitVision" from the application store to download and install 
the BitVision App.

Android App QR

iOS App QR

Step 2: Account login

Run BitVision App, click "        " in the sliding sidebar, enter the account 
name and password, and click “Login” (Note: no account is required to 

register first).

Step 3: Add device

After login, click "Device manage" ,  "       " and "        Add device" , 
select "SN Add", enter the device user name, password and verification 
code after scan the QR code (the verification code printed on the 

label), click "Submit" to set device name and group, click "Finish" and 

the addition is successful.

Step 4: Live preview

Select "Real time" and "           " to enter the device list in the main 

interface, select the device channel to be previewed in the group, you 

will see the live video after click " Done ".

5

Содержание DFR-5MP-XVR4









Отзывы: