background image

GB

5

1

2

1 . 5  

c m

The mounting bracket is designed for use on uneven

surfaces. Remove the bracket from the heater by

pushing it backwards.  The bracket is mounted by

means of the enclosed distance sleeves (1) shown in

the picture to the right.  All the holes in the bracket

can be used, but it is desirable for the mounting

points to be as far apart as possible. Use the enclos-

ed 3 screws to fasten the mounting bracket. The dis-

tance sleeves must be removed before the bracket is

mounted. Guide the interior heater onto the bracket

and push (2) until a click is heard.

The interior heater must be positioned so that it does not constitute a safety

hazard in case of a collision or hard braking.

When used in a vehicle the interior heater must always be connected to a power socket

mounted in the interior and connected to a power outlet on the outside with intercon-

necting lead or mini-plug. Only original DEFA connector kits with original

DEFA Mini-Plug may be used. The lead may only be connected to an earthed power

socket.

Make sure that screws or drill bits do not damage cables or control units on

the back of the panel where the mounting bracket and the plug is fitted.

Installation of the DEFA Mini-Plug and interconnecting cables

Fitting of DEFA Mini-Plug.

Recessing the Mini-Plug.

The DEFA Mini Plug should be mounted in such a way that it is

protected against splash and mechanical damage and so that the con-

nector lead can be connected without difficulty. When the mounting

surface for the fastening nut is uneven the enclosed mounting ring

should be used. Insert the O-ring is in the groove in the plastic nut

or on the mounting ring if this is used. Drill a hole with a diameter

of Ø24,5 mm and file a guide groove with a diameter of Ø3 mm to

recess the Mini plug. (Special tool no. 460840).  Make sure there is sufficient space in the

rear for the cable and enough room for the fastening nut. Be careful when drilling so that

mounted components, cables etc. are not damaged. The plug can be painted, if desirable,

in the car’s own colour.

Содержание Warm Up









Отзывы: