manualshive.com logo in svg

DEEP SEA ELECTRONICS DSECONTROL DSE7000 Series, Руководство оператора

Поделиться
Скачать
DEEP SEA ELECTRONICS DSECONTROL DSE7000 Series Скачать руководство пользователя страница 60

DSE Model 7000 Series Control and Instrumentation System Operators Manual 

60    

Part No. 057-074   7000 Series OPERATING MANUAL ISSUE 2  02/05/2008 ADM 

 

8.4  SHUTDOWNS 

 
Shutdowns are latching alarms and stop the Generator. Clear the alarm and remove the fault then press Stop/Reset 

 

to reset the module. 

 
Example 

Alarm        1/1 

 

Oil Pressure Low 
Shutdown 

 

 

NOTE:- The alarm condition must be rectified before a reset will take place. If the alarm condition 

remains, it will not be possible to reset the unit (The exception to this is the Low Oil Pressure alarm and 
similar ‘delayed alarms’, as the oil pressure will be low with the engine at rest). 

 

Display 

Reason 

EARTH FAULT 
(DSE7300 series V2.0.0 or above 
only) 

The measured Earth Fault Current has been in excess of the earth fault 
trip and has surpassed the IDMT curve of the Earth Fault alarm. 

FAIL TO START 

The engine has not fired after the preset number of start attempts 

EMERGENCY STOP 

The emergency stop button has been depressed. This a failsafe (normally 
closed to battery positive) input and will immediately stop the set should 
the signal be removed. 
Removal of the battery positive supply from the emergency stop input will 
also remove DC supply from the Fuel and Start outputs of the controller. 

NOTE:- The Emergency Stop Positive signal must be present 

otherwise the unit will shutdown. 

 

LOW OIL PRESSURE 

The engine oil pressure has fallen below the low oil pressure trip setting 
level after the Safety On timer has expired. 

ENGINE HIGH  TEMPERATURE 

The engine coolant temperature has exceeded the high engine 
temperature trip setting level after the Safety On timer has expired. 

PHASE ROTATION 
(DSE7000 series V2.0.0 or above 
only) 

The phase rotation is measured as being different to the configured 
direction. 

OVERSPEED 

The engine speed has exceeded the pre-set trip 
 

NOTE:-During  the  start-up  sequence,  the  overspeed  trip  logic 

can be configured to allow an extra trip level margin. This is used to 
prevent  nuisance  tripping  on  start-up  -  Refer  to  the  7000  series 
configuration 

software 

manual 

under 

heading 

‘Overspeed 

Overshoot’ for details. 

 

UNDERSPEED 

The engine speed has fallen below the pre-set trip after the Safety On 
timer has expired. 

GENERATOR OVER FREQUENCY 

The generator output frequency has risen above the preset level 

GENERATOR UNDER FREQUENCY 

The generator output frequency has fallen below the preset level 

GENERATOR OVER VOLTAGE 

The generator output voltage has risen above the preset level 

GENERATOR UNDER VOLTAGE 

The generator output voltage has fallen below the preset level 

Содержание DSECONTROL DSE7000 Series















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды