Dectris PILATUS 3 R 100K-M Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 39

Dectris PILATUS 3 R 100K-M Скачать руководство пользователя страница 23

4.2. Detector Control Unit

4.2.1. Configuration of the Detector Control Unit

Please do not install or run any other software on the computer, except tools and software which are necessary for config-
uring your data acquisition protocol.
The detector control unit is set up with a standard installation of the CentOS 7.x distribution. Regular system updates can
be made. However, to avoid operational deterioration do not update the system while the detector is taking data.

Caution

#10

Do not remove the symbolic link in the directory

~/p2_det/images

, which points to the

images

directory.

The detector control unit has to be connected point-to-point to the detector via 1 x 1Gb Ethernet. The detector control unit
can be integrated into the site network infrastructure using one of the interfaces described in section 4.2.2. The detector
control unit is optimised for performance and stability of operation. In order to achieve these goals we deliver the detector
control unit with fixed firmware (bios etc.) and software (OS) version.

Figure 4.13:

PILATUS3 R 100K-M detector control unit as seen from the front.

Caution

#11

Pushing the power button on the front panel longer than 2 seconds will immediately halt the detector control
unit. All image data on the detector control unit will be permanently lost.

Information

#5

Briefly pushing the power button on the front panel will shut down the detector control unit. May take up to
1 min.

Figure 4.14:

PILATUS3 R 100K-M detector control unit as seen from the back.

4.2.2. Connectors

Table 4.5:

Detector Control Unit Connectors

Connector

Description

EM1 (Embedded, figure 4.14)

1 GBase-T adapter
labeled as LAN
User configurable GbE Network Interface
Preconfiguration: DHCP

PILATUS3 R 100K-M Technical Specifications v1.2.2

18 | 34

«
...
21
22
23
24
25
...
»

Содержание PILATUS 3 R 100K-M








































Отзывы:

Нет отзывов