6. Cancelling the Pairing & Limits
6.1 If all the limits and pairing need to be deleted then press the P2 button, stop and then the P2
button ag
a
in. The handset will now need to be re-paired to the Motor.
7. Reversing the Direction of a Motor
7.1 Press and hold the programming button on the motor until the blind steps. The direction of the
motor should be reversed.
8. Adding an Additional Handset
8.1 Press the P2 button twice on the original handset and then the P2 button on the handset
that is to be added (allow 1 second between pressing each button).
8.2 The motor should beep to confirm that the pairing has been successful.
9. Extra Information
9.1 Approximate range of hand-held remotes with obstruction (such as a wall): 35m.
9.2 If you are adding more than one blind to a channel, ensure that all other blinds paired to that channel
have the power turned off. Once the other blind has been paired and had the limits set the other blinds
can be turned back on.
10. Troubleshooting
* Multi-channel remotes only
10. Further Support
10.1 Please contact your local distributor.
Cura Roller Blind Motor
Programming Instructions
1. Pairing the Handset
1.1 *15 Channel Handset Only *Select the channel on the handset that you wish
to pair the blind to. [Please note that you cannot pair blinds to Channel 00.]
1.2 Press and hold the programming button on the motor. Alternatively, if the
motor is not easily accessible and you are using a power adapter, you can turn the
power to the motor off and back on again. The motor should step and beep.
1.3 Press the P2 button (labelled as Setup or P2) on the back of the handset twice then the up button. This
must be done in a smooth rhythm (allow 1 second between pressing each button). The motor should beep
and step to confirm that the pairing is complete.
1.4 Check that the motor is running in the correct direction. (I.e. Press the up button and the blind goes up).
If required, refer to section 7 to change the motor direction.
1.5 All blinds paired to a handset will all automatically work together when you select channel 00.
2. Setting the Limits
2.1 Wake up the handset by pressing any button, apart from up or down.
2.2 Press the P2 button in the back of the handset then the up button and then the P2 button again
(allow 1 second between pressing each button). The motor should beep and step.
2.3 Make the blind go up. When the blind is near the upper limit press the P2 button on the handset and
the blind will step up slowly. Stop the blind in the desired upper limit position. Press stop 5 times, or until the
blind steps. The motor should beep every time you press stop.
2.4 Make the blind go down. When the blind is near the lower limit press the P2 button on the
handset and the blind will step down slowly. Stop the blind in the desired lower limit position. Press stop 5
times, or until the blind steps. The motor should beep every time you press stop.
2.5 The limits have now been set. Test this by pushing the up and down buttons to make sure that the
blind stops in the correct positions. [Please note that you must set both top and bottom limits before
testing the limits.]
3. Adjusting the Limits
3.1 To adjust the limits repeat the process for setting the limits.
4. Cancelling the Limits
4.1 To cancel the limits press the P2 button, down and then the P2 button again (allow 1 second
between pressing each button). You will now need to reset all the limits.
Issue
Possible Cause
Solution
The blind is not responding
to the remote
The blind has no power
The blind is not paired to the remote
The battery in the remote is flat
The incorrect channel is selected*
Check the power / batteries
Follow steps 1 & 2
Replace the battery
Select the correct channel
The blind is stopping in the
incorrect position
The limits are set incorrectly
Reset the limits shown in stage 2
You press up but the blind
goes down
The motor is running in the wrong
direction
Change the direction of the motor
(see section 6)
The blind is not pairing
The remote has channel 00 selected
Choose a different channel
Programming
Button
Cura Motor
