DECODE PRM4 Скачать руководство пользователя | Manualshive

Страница: 18 / 20

background image

5 Firmware update

The following is needed to load the new version of the firmware into the PRM4
device:



MSPFET software

– Can be located on the CD that is included in the PRM4

product pack. Otherwise, the latest software version can be downloaded from
http://kurt.on.ufanet.ru/files/MspFet_16007_devel.zip



RS232 cable for programming

the PRM 4 device, and



File containing the new firmware

.

5.1 The procedure for writing the new firmware



Open the casing of the device and take out the printed circuit board.



Connect the serial port of the PC to RS232 port of the modem via DB9 cable
and programming cable. The adapter for PRM 4 is DB9 female to DB9 male
cable with the following pin connections:

DB9 female

DB9 male

pin 2 ------------------- pin 8
pin 3 ------------------- pin 7
pin 4 ------------------- pin 4
pin 5 ------------------- pin 5
pin 7 ------------------- pin 3



Set the J1 and J2 into the 1-2 state. The rest of the jumpers should be in a state
corresponding for RS-232C serial connection according to the aforementioned
table.



Connect the power supply.



Start the MSPFET, load the prm4xxx.hex, using the setup of the program
adjust the BSL and serial port to which the device is connected. Press AUTO.
Confirm that the modem's microcontroller has been programmed and verified.



Disconnect the power supply.



Set the J1 and J2 into the 2-3 state.



Return the circuit board into the casing and close it.



Check the modem operation with the new firmware.

Radio modem PRM4 868MHz /User's manual V1.6 / 24.05.2011

18

«
...
16
17
18
19
20
»

Содержание PRM4





















Отзывы:

Нет отзывов

Похожие инструкции для PRM4

Бренд: NAL Страницы: 180

Бренд: NAL Страницы: 107

Бренд: Marquant Страницы: 12

Бренд: US Robotics Страницы: 2

Бренд: OUMAN Страницы: 6

Бренд: Jensen Страницы: 14

Бренд: MAJORITY Страницы: 20

Бренд: Mitsubishi Страницы: 47

Бренд: RACEceiver Страницы: 2

Бренд: Grundig Страницы: 38

Бренд: Teac Страницы: 100

Бренд: EBENCH Страницы: 8

Бренд: Globalstar Страницы: 36

Бренд: KaiDeng Страницы: 4

PathFinder3 SART-3

Бренд: ACR Electronics Страницы: 20

Бренд: Hitachi Koki Страницы: 2

Бренд: Honeywell Страницы: 2

Бренд: Kenwood Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды