DeAGNOSTINI MODEL SPACE Red Bull Racing RB7 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 32

background image

Red Bull Racing RB7: Step by Step

™

496

13

Next, remove the three circled screws from the front end of your model. If the rear

screw is difficult to take out, press down carefully on the pushrod mount so that you

can get a hold of the screw’s head.

14

Turn the model over and remove

the two circled screws.

11

The next phase is to mount the front wing onto your RB7’s chassis. To begin,

lower the lower nose brace supplied with Stage 29 onto the rear of the front wing

assembly, as shown by the red arrow. The parts will fit neatly when properly aligned.

12

Holding the parts together, turn

the assembly over and insert

one of the 3 x 8mm countersunk screws

into each of the two holes (see arrows).

Tighten these fully with a screwdriver.

«
...
11
12
13
14
15
...
»

Содержание Red Bull Racing RB7

































Отзывы:

Нет отзывов

Похожие инструкции для Red Bull Racing RB7

FEBER trimoto Disney Princesita Sofia

Бренд: Famosa Страницы: 2

Бренд: SWorkz Страницы: 44

Бренд: Team C Страницы: 35

Бренд: e-Gizmo Страницы: 27

DodgeViper GTSR Supercharged Racer 60-4340

Бренд: Radio Shack Страницы: 8

X-Factor Nitro Monster Truck

Бренд: XTM Racing Страницы: 16

Бренд: Arrma Страницы: 44

GRANITE 4x4 MEGA

Бренд: Arrma Страницы: 48

Бренд: Arrma Страницы: 40

Бренд: Arrma Страницы: 44

Бренд: Arrma Страницы: 52

Disney Princess S-Miles

Бренд: Famosa Страницы: 2

Бренд: WRC Страницы: 12

Бренд: WRC Страницы: 14

Aston Martin Racing DBR9 Le Mans 2006

Бренд: Kyosho Страницы: 10

Бренд: T.O.P. Racing Страницы: 22

Atsushi Hara edition Pro4

Бренд: HPI Racing Страницы: 44

DBX VE Readyset

Бренд: Kyosho Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды