manualshive.com logo in svg

DCS MO-24-SS, Техническое обслуживание руководство

Поделиться
Скачать
DCS MO-24-SS Скачать руководство пользователя страница 19

17

COMPU DEFROST TEST
WARNING : The oven should be fully assembled before following procedure.
(1) Place one cup of water in the center of the turntable tray in the oven cavity.
(2) Close the door, touch the Defrost pad and touch the number pad 5 twice.

Then touch the start pad.

(3) The oven is in Compu Defrost cooking condition.
(4) The oven will operate as follows
                                         1ST STAGE

      2ND STAGE

WEIGHT

LEVEL

TIME

LEVEL

TIME

0.5lb

70%

30sec.

40%

15sec.

(5) If improper operation is indicated, the control unit is probably defective and should be checked.

6. Re-install the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.

TEST PROCEDURES

PROCEDURE

LETTER

COMPONENT TEST

1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power transformer.
5. Ensure that these leads remain isolated from other components and oven chassis by using insulation

tape.

6. After that procedure, re-connect the power supply cord.
7. Remove the outer case and check voltage between Pin No. 1 of the 2 pin connector (A) and the

common terminal of the relay RY1 on the control unit with an A.C. voltmeter.
The meter should indicate 120 volts, if not check oven circuit.

     RY1 and RY2 Relay Test

 These relays are operated by D.C. voltage
 Check voltage at the relay coil with a D.C. voltmeter during the microwave cooking operation.

DC. voltage indicated ............. Defective relay.
DC. voltage not indicated ........ Check diode which is connected to the relay coil. If diode is good,

control unit is defective.

 

RELAY SYMBOL             OPERATIONAL VOLTAGE                                CONNECTED COMPONENTS

          RY1                                 Approx. 24.0V D.C.                        Oven lamp / Turntable motor / Cooling fan motor

          RY2                              Approx. 23.0V D.C.

                                                                      

Power transformer

 8. Disconnect the power supply cord, and then remove outer case.

  9. Open the door and block it open.
10. Discharge high voltage capacitor.
11. Reconnect all leads removed from components during testing.
12. Re-install the outer case (cabinet).
13. Reconnect the power supply cord after the outer case is installed.
14. Run the oven and check all functions.

L

K

RELAY TEST

                                         MO24SS

G 1

G 2

G 3

G 4

G 5

G 6

G 7

G 8

G 9

G10

G11

G12

G13

G14

FRESH

VEGETABLES

BEVERAGE

BREAKFAST

MENU

LUNCH

MENU

POPCORN

FROZEN
SNACKS

QUICK

RECIPES

START

TOUCH START

FISH

SEAFOOD

POWER

LEVEL

KEEP

WARM

DINNER

MENU

DEFROST

HELP

MENU

BAKED

POTATOES

SENSOR

REHEAT

EXTRA

MINUTE

FROZEN

VEGTABLES

RICE

1

6

2

7

3

8

4

9

5

0

POULTRY

GROUND

MEAT

Frozen

Entrees

TIMER

CLOCK

STOP

CLEAR

Содержание MO-24-SS













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды