manualshive.com logo in svg

DCS DD24DVT7, Руководство по установке

Поделиться
Скачать
DCS DD24DVT7 Скачать руководство пользователя страница 5

5

OPTIONALLY HARD WIRING PRIOR TO INSTALLATION

9

12

11

11

10

4

5

6

7

7

8

8

3a

3c

3

3b

REMOVE THE LOWER DRAWER

TERMINATE THE WIRING AS SHOWN

REMOVE THE ACCESS COVER & POWER CORD

100 mm

2

4

5

1

4” (100mm)

To prevent kinked hoses, we recommend 

rotating the drawer anti-clockwise and 

resting it on its side after removal.

Access 

cover

Press the release tabs in on

either side and push back

to release drawer from

runners.

3

Remove knock-out for cable clamp and 
fit a suitable cable clamp for the conduit.

Use copper conductors only.

3d

REFIT THE DRAWER ONTO THE RUNNERS & CLOSE

13

14

15

16

19

Before refitting the drawer, 

ensure the hoses are not 

twisted and the latches at 

the rear of each drawer 

runner are facing forward. 

Ensure the release tabs on 

both sides are reset fully.

Ensure the drawer 

is now rotated 

clockwise back.

Pull for

ward the r

elease tabs

 

on both sides 4”(100 

mm)

Electrical Shock Hazard

Before continuing, ensure that the product is 
disconnected from the power supply.

Failure to follow this warning may result in
electrical shock, injury or fire.

WARNING!

Содержание DD24DVT7


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды