DCS CAD-36 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 23

DCS CAD-36 Скачать руководство пользователя страница 12

12

INSTALLATION

First you will need to remove the angle
brackets from the side of the unit and replace
them with cart mount brackets.
Note: grill is shipped prepared for island
installation.

Install the bracket tab on both sides using
eight of the 10-24 x 1/2" screws. Install each
bracket with four screws on each side of
the grill head. For a CAD1-48/48, use the
appropriately labeled bracket for your grill
head and cart side.

1

2

Outdoor appliance head preparation

IMPORTANT!

For the CAD1-48/48 there are two sets of brackets. If you have the

BGB48-BQR, use the brackets labeled LEFT-48 BQR and RIGHT-48 BQR.

If you have the BGB48-BQAR or BE1-48, use the brackets labeled 48-BQAR

3

LPG models only:

Remove the gas compartment drawer for
access to the gas hatch cover. Refer to page
19 for details.

4

Using a Phillips screwdriver, remove the screw
holding the hatch cover in place. Slide the
hatch cover out.

«
...
10
11
12
13
14
...
»

Содержание CAD-36
























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды