background image

2-Way, 3-Way

4-Way Crossovers

223/223XL - 234/234XL

234/234XL-223/223XL R

EAR

P

ANEL

O

PERATIONS

M

ODE

S

WITCHES

234XL R

EAR

P

ANEL

234 R

EAR

P

ANEL

The mode switches on the back panel of the unit are used to select one

of the three modes of operation in the 234/234XL and one of two modes

of operation in the 223/223XL. There could be disastrous consequences

if the crossover were improperly setup or the switches were mistakenly

pushed during the regular operation of a sound system. Therefore great

care should be taken when setting these switches. There is a mode dia-

gram on the back panel to help you understand at a glance how this is

done. The following steps should be taken in setting up your system:

• Know the loudspeaker manufacturer’s requirements regarding the

amplification needs of your particular speaker system. Follow the

maunfacturer’s guidelines carefully, as dbx is not responsible for dam-

age relating to improper setup or implementation of the 234/234XL-

223/223XL.

• Without any audio or power connections in place, use the back panel

switches on the crossover to set it to the proper mode of operation;

either stereo 2-way, stereo 3-way, or mono 4-way for the 234/234XL,

or stereo 2-way or mono 3-way for the 223/223XL.

• Use the literature that came with your speaker system to properly set

up the mode of operation and crossover frequencies to the manufac-

turer’s specifications.

• There is one of the four possible mode button combinations for the

234/234XL which is marked “not valid”. Be sure you have not select-

ed this combination as the 234/234XL will not operate correctly in this

mode.

When you are certain that the proper selections have been made, com-

plete the steps described below and in the “234/234XL-223/223XL Audio

Connections” section on page 7.

6

®

CHANNEL TWO

MODE

MID

HIGH-MID

x 1

x 10

HIGH

HIGH

LOW

NOT USED

INPUT

NOT USED

CHANNEL ONE

HIGH

LOW/MID

NOT USED

HIGH

STEREO 3-WAY

MONO 4-WAY

STEREO 2-WAY

LOW

INPUT

LOW/HIGH

NOT USED

NOT USED

MID

LOW-MID

LOW/MID

LOW/LOW-MID

x 1

x 10

STEREO 3-WAY
STEREO 2-WAY

MONO 4-WAY

NOT VALID

LOW/LF SUM

LOW

INPUT

HIGH

NOT USED

LOW/HIGH

LOW/LF SUM

INPUT

INPUT

LF SUM

LOW SUM
LOW SUM

NORMAL

SUMMED

ONLY

A HARMAN INTERNATIONAL
COMPANY
SALT LAKE  CITY, UTAH
MADE IN USA
MODEL 234

®

PROFESSIONAL PRODUCTS

XOVER FREQ

XOVER FREQ

15 WATTS

100V      50/60Hz

120V      60Hz

Содержание 223/223XL

















Отзывы:

Похожие инструкции для 223/223XL