VIO X310
420120424Q REV1.0
QUICK START USER MANUAL SECTION 1
2
Data Out
Data In
R
RD
DN
Neett
Link
Active
Remote
Preset Active
Expansion Card
Balanced Audio
USB Data Service
Push and hold
to test
System Test
Ready
Limiter
Signal
Mute/Prot
Status
100-120V~ (T10A L 250V~)
220-240V~ (T5A L 250V~)
(REPLACE FUSE WITH SAME RATINGS)
(REMPLACER LE FUSIBLE AVEC LE MÊME TYPE)
220-240V~ 14,2Amax
3200Wmax
100-120V~ 16,3Amax
1800Wmax
220-240V~ 50-60Hz 1,8A
100-120V~ 50-60Hz 3,7A
FULL RANGE
MAINS INPUT
100-240V~ 50-60Hz
MAINS FUSE
MAINS LINK
This device complies with part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
Serial Number
AEB INDUSTRIALE S.R.L.
Via Brodolini, 8
Località Crespellano
40053 VALSAMOGGIA (BO)
ITALY
CAUTION
RISK OF
ELECTRICAL
SHOCK
DO NOT OPEN
ATTENTION
RISQUE DE
CHOCH
ELECTRIQUE
NE PAS OUVRIR
WARNING
HOT SURFACE
DSP Preset
Fullrange
Service/User
HPF
[Hz]
60
65
70
75
80
90
ON
X
X
Data Out
Data In
R
RD
DN
Neett
Link
Active
Remote
Preset Active
Expansion Card
Balanced Audio
USB Data Service
Push and hold
to test
System Test
Ready
Limiter
Signal
Mute/Prot
Status
100-120V~ (T10A L 250V~)
220-240V~ (T5A L 250V~)
(REPLACE FUSE WITH SAME RATINGS)
(REMPLACER LE FUSIBLE AVEC LE MÊME TYPE)
220-240V~ 14,2Amax
3200Wmax
100-120V~ 16,3Amax
1800Wmax
220-240V~ 50-60Hz 1,8A
100-120V~ 50-60Hz 3,7A
FULL RANGE
MAINS INPUT
100-240V~ 50-60Hz
MAINS FUSE
MAINS LINK
This device complies with part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
Serial Number
AEB INDUSTRIALE S.R.L.
Via Brodolini, 8
Località Crespellano
40053 VALSAMOGGIA (BO)
ITALY
CAUTION
RISK OF
ELECTRICAL
SHOCK
DO NOT OPEN
ATTENTION
RISQUE DE
CHOCH
ELECTRIQUE
NE PAS OUVRIR
WARNING
HOT SURFACE
DSP Preset
Fullrange
Service/User
HPF
[Hz]
60
65
70
75
80
90
ON
X
X
5
6
1
2
3
4
I/O and Control panel
The DigiPro G4 amplifier of VIO X310 is controlled by a
powerful DSP. All the connections and controls are in the
rear amplifier control panel.
1-
B-type USB port for firmware updating
2-
RDNet Data In / Data Out and Control LEDs
3-
Balanced audio input and output link
4-
DSP Preset rotary switch (High Pass Filter)
5-
System Test
6-
Status LEDs (Limiter, Signal, Mute/Protection,
Ready)
7-
Full-range Mains input
8-
Mains Link output
9-
Mains Fuse
8
7
9
POWER SUPPLY SPECIFICATIONS (POWER ABSORPTION)
Draw at 1/8 of full power in average use conditions (*): 0,8 A (220-240V~) - 1,5 A (100-120V~)
Draw at 1/3 of full power in maximum use conditions (**): 1,8 A (220-240V~) - 3,7 A (100-120V~)
Power absorption with speaker turned on without signal (idle): 0,25 A (220-240V~) - 0,28 A (100-120V~)
*INSTALLER NOTES: The values refer to 1/8 of full power, in average operating conditions (music program with infrequent or no clipping). It is
recommended to consider them the minimum sizing values, for any type of configuration.
**INSTALLER NOTES: The values refer to 1/3 of full power, in heavy operating conditions (music program with frequent clipping or activation of
the limiter. We recommend sizing according to these values in case of professional installations and tours
VIO X310 is the new dB Technologies 3-way active speaker for professional use. It is equipped with one coaxial neodymium transducer (MF voice coil:
4”, HF voice coil: 2,5”, HF exit: 1.4”) and two 10” neodymium woofers (2.5” voice coil). The coverage pattern is 90° (H) x 40° (V). The horn is rotatable
and the mechanical design allows an easy, accurate and quick installation for stand or flyable use thanks to the optional brackets. The powerful Digi-
Pro G4 amplifier section, capable of handling up to 1400 W (RMS power), is controlled by a DSP, which can perform a detailed customization of the
output sound of the speaker. In addition, the integrated RDNet connections are useful for a remote in-depth control and configuration using AURORA
NET software.
Setup, turn on and I/O settings
Connect first the audio input (1); to link the audio signal to
another speaker, please use a cable with XLR connectors
(not supplied). Connect the Output Link of the first, to the
balanced Input of the second one, and so on.
Plug properly the mains POWERCON TRUE1 cable (sup-
plied) in the related input (7) to turn on the system. To
supply power to another speaker connect the Mains Link
output of the first speaker to the Mains Input of the se-
cond one and so on. To find out how many modules can
be connected in a linked system, refer to the “TECHNICAL
SPECIFICATIONS” or “CONNECTIONS” sections in the VIO
X310 user manual.
In case of remote control, connect the Data Input of the
speaker to the hardware remote controller (RDNet Control
2 or RDNet Control 8) with cables equipped with etherCON
connectors. Connect the Data Output of the first, to the
Data Input of the second one, and so on. When the spe-
aker is active and the RDNet network is active and it has
recognized the connected device, the LED Link is on. The
“Active” LED start blinking when there is the presence of
data trasmission, the “Remote Preset Active” advise that all
the local controls set on the amplifier panel (DSP preset)
are by-passed and controlled remotely by RDNet.
See also RDNet Control 2 or RDNet Control 8 user manuals
for further information.
