DayTronic PC-HSICA Скачать руководство пользователя страница 2

Copyright © 1996, Daytronic Corporation.  All rights reserved.

No part of this document may be reprinted, reproduced, or used in any form or by
any electronic, mechanical, or other means, including photocopying and recording,
or in any information storage and retrieval system, without permission in writing from
Daytronic Corporation.  All specifications are subject to change without notice.

PC-HSICA is a trademark of Daytronic Corporation.

FCC Radio Frequency Compliance

Note: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules.  These limits are designed to provide rea-
sonable protection against harmful interference when the
equipment is operated in a commercial environment.  This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications.  Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his own
expense.

Содержание PC-HSICA














Отзывы: