manualshive.com logo in svg

DaytonAudio DSPB Series, Руководство пользователя

Поделиться
Скачать
DaytonAudio DSPB Series Скачать руководство пользователя страница 8

C.

 

Combining a DSPB Amplifier with a KAB Amplifier 

–

 Quick Start 

This section assumes you have already read the Quick Start guide for the DSPB-250/100 which is directly 
previous to this section. 

1)

 

How to Power the Amplifiers 

a)

 

The easiest method is to parallel the power connectors that come with all DSPB and KAB 
amplifiers (physically tie the red wire for each connector together, and the same with the 
black wire), and wire them to a single DC power jack (while observing the proper polarity 
that your power supply requires).  
i)

 

Alternatively, the end connector of a 12-24V power supply can be cut off and the red 

and black wires of the wiring harness’ can be connected directly to the power supplies 

positive and negative wires. You might find this method to be useful during testing, if 
you want to quickly get them powered and are without a bench power supply, but likely 
not for a finished product. 

b)

 

For battery power, it is recommended to use the KAB-BE battery board, connected to the 
KAB and DSPB in the way the diagram shows below. Note that J9, J10, and J11 all serve the 
same function on the KAB-BE, so you can connect your KAB or DSPB to any of these ports. 
i)

 

NOTE: Only the KAB amplifier can charge the KAB-BE (through J3 on the KAB). The DSPB 
will not be able to charge the KAB-BE.  

 

2)

 

Sharing Audio Between the Boards 

1.

 

Connect J5 on the DSPB amplifier to J11 on KAB amplifier with a 6 pin cable (this connection 
shares the audio back and forth between the boards).  (See the image below) 

2.

 

This connection allows for the following 

a.

 

Bluetooth can be used as an input for the DSPB amplifier 

b.

 

The KAB amplifier’s powered outputs can receive processed signals from the DSPB, even 

when using Bluetooth as a source. 

c.

 

The end result of this connection is up to 4 channels of individually processed audio. For 
an example of how to do this processing, see example 2.E or 2.F in the Sigma Studio 
Examples section for how to utilize the 4 channels of DSP, or simply use the built-on 
potentiometers to make basic adjustments without SigmaStudio. 

Содержание DSPB Series
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды