(From Pre-amp or Receiver Line Out)
L
R
WARRANTY COVERAGE
Dayton Audio products are warranted to be free of all defects in material and workmanship for 5 YEARS from the date of purchase from
an authorized Dayton Audio dealer. This warranty and all rights provided are limited to the original owner and are non-transfer able.
Dayton Audio's responsibility is limited to replacement or repair as set forth in this warranty statement.
Should a product require warranty service during this period, Dayton Audio will repair or replace without charge, any part or product
proving defective in material or workmanship. All warranty repairs and service must be performed by an authorized Dayton Audio
technician or service facility. The use of non-authorized repair services renders this warranty null and void, and any charges
relating to non-authorized repair are the responsibility of the product owner.
All expenses related to replacing or repairing a defective part or product under this warranty shall be assumed by Dayton Audio.
Dayton Audio reserves the right to replace defective product with a new or factory reconditioned unit.
WARRANTY EXCLUSIONS
1. This warranty does not cover product failure or damage resulting from misuse, abuse, neglect, accidents, alterations, standard
environmental deterioration, natural disasters, or improper use and/or installation.
2. This warranty does not cover cosmetic damage due to misuse or neglect. This includes paint damage, scratches, cracks or other
superficial marks related to improper use.
3. Failures arising from attempted servicing of a non-authorized Dayton Audio repair facility or technician are excluded from this warranty.
LIMITATION OF DAMAGES
In no event shall Dayton Audio be liable for consequential damages for breach of this warranty including installation charges, excessive
shipping expenses, property loss or other incidental loss. Some States do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to the buyer.
HOW TO OBTAIN WARRANTY SERVICE
To obtain services under this warranty, the buyer shall contact Dayton Audio's authorized service provider, Parts Express, at
1-800-338-0531 x 780 to obtain a return authorization number (RA#).
The buyer must carefully pack the warranted product along with a copy of the original purchase receipt, the return authorization number
(RA#), and a description to the repair facility listed below. Shipping for warranty service is the responsibility of the buyer.
Parts Express
Attn: Dayton Audio Warranty Repairs RA# (please write your RA# here)
705 Pleasant Valley Drive
Springboro, Ohio 45066
NOTICE TO BUYER
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
5
daytonaudio.com
tel + 937.743.8248
[email protected]
705 Pleasant Valley Dr.
Springboro, OH 45066
USA
Dayton Audio
®
Last Revised: 8/9/2016
L
R
(From Local Source Line Out) (From Pre-amp Line Out) (Out to Additional Zones)
APPLICATIONS
STEREO SETUP
In this configuration, the mode switch is set to “Stereo”. Connect the line out
jacks from a stereo pre-amplifier or source to the MAIN input jacks of your
APA102. Next connect your speakers to the terminals marked “Speaker A”
observing proper polarity. Select the “A” speakers using the front panel zone
selection buttons. Connect a second (optional) pair of speakers to the
terminals marked “Speaker B”. If you are connecting 4 speakers to the
APA102 they must be 8 ohm speakers only. Press A and B together to use
both zones.
SETUP FOR MULTIPLE SOURCE
In the multiple source set up, a distributed audio system is connected to the
APA102 as a local zone amplifier via the MAIN inputs. Normally the distribut
-
ed audio system will be the audio source for the APA102 . The distributed
audio is then passed on to be used by additional zones or sub zones in the
distributed system via the MAIN outputs.
Note:
Main Out only duplicates what source is connected to the Main Input,
ideal for adding additional Amplifier or connect to Power Subwoofer.
The audio output of a local source, such as an MP3 Player, CD, television,
computer, etc., is connected to the APA102 via the INTERRUPTIN G inputs,
and whenever the local source is active its signal will take priority over the
distributed audio signal present at MAIN input . However, the distributed
audio signal will still be present at the MAIN input. In this circumstance the
audio output of the local source will be heard via the APA102. Once the local
source is turned off or muted, the APA102 will automatically switch back to
the distributed audio system as an audio source, assuming the local source
remains inactive. There is a delay of up to 6 seconds when switching from
INTERRUPTING input back to MAIN inputs.
