2 of 4
‘Lower’ functions either on a faceplate and/or a switch on input 1. Once
the system has been allowed to ‘time out’, light level will revert to the
default light level setting as above.
SWITCH INPUTS - OPERATION & DEFAULTS
The SET-DLCM3 and SET-DLCM5 have 5 x switch inputs which can be
used for various manual control options. There are also specific inputs
for ‘Emergency Test’ and ‘Override’. See ‘Inputs/Outputs And Status
LED’s’ on page 3 and the ‘Switch Functions Table’ below for further
details.
Switch 1:
By default, this switch input is programmed to operate as ‘On’,
‘Off’, ‘Raise’ and ‘Lower’ using a momentary push switch.
Switch 2:
Test Mode. A momentary switch wired to this input can be
used to activate ‘Test Mode’. The switch can be used to toggle between
on and off. With test mode on, the system will time out after occupancy
has ceased and switch lighting off after 10 seconds. A secondary
function of this switch is to allow you to invoke a ‘System Reboot’. Press
and hold the switch for more than 5 seconds then release. The device
will restart without losing any previously programmed settings.
Switch 3:
Programming Mode. A momentary switch wired to this input
will allow some quick and simple programming options to be selected. A
short press on this switch will toggle between DSI & DALI dimming
modes. A long press will store the currently selected scene’s output to
memory. Set your desired lighting output level by using the raise/lower
buttons on a faceplate or a switch wired to switch input 1. Store this level
with a long press on switch 3.
Another function of this switch is to enable a quick method of invoking a
‘Factory Reset’. Press and hold the switch for more than 5 seconds then
release. The device will reboot with all previously programmed settings
being cleared from memory.
Switch 4 & 5:
These switch inputs are not programmed on leaving the factory for any
particular function and can be programmed as required.
Switch 6: Emergency Test (E-TS):
Input for standard ‘Keyswitches’ to
allow emergency lighting to be tested. By default the normal lighting will
turn off whilst discharging the emergency lighting. (Can be programmed
to keep the normal lighting on whilst discharging the emergency lighting)
This function affects all ‘Output’ devices on the same network.
Switch 7: Override (O-RD):
By default this input is programmed to allow
for a complete system override either from a switch or volt-free contact.
On operation, the lights will go to full output with all inputs from any input
devices or sensors being ignored. May be used for interfacing with alarm
or BMS systems etc.
MODES OF OPERATION
The following table describes some basic ‘Modes Of Operation’
based on types of input, such as occupancy sensors, light level
sensors, switches and faceplates.
All methods connect to the RS485 network, either by direct connect-
ion at a specific device or through a SET-DPP (Daylux Programming
Port). The SET-DHPP also has the ability to use an IR (Infra-Red)
Link as a means of connecting to the network. Please see the
‘SET-DPP User Guide’, the ‘SET-DFP User Guide’, the ‘SET-DHHP
User Guide’ and the ‘SET-DPCS User Guide’ for further information
and programming instructions. Please contact Setsquare for any
programming requirements. (Contact details on back page).
Once the systems have been commissioned, the default settings
most likely would have been changed to specific requirements for the
site. If Setsquare undertake the commissioning, these settings are
recorded in an engineer’s report which is issued in the handover
documentation for the project.
CHANGING DEFAULTS SETTINGS - PROGRAMMING
The SET-DLCM is part of the DLCS range of products which are fully
networkable and programmable. It is possible to change any of the
default settings (program) for time delay, automatic light level,
dimming protocol change between DSI and DALI (SET-DLCM3-D
& SET-DLCM5-D only), manual scene levels and associated channel
selection, occupancy inputs and associated channels, switch input
configuration, network commands (such as corridor hold, group
control and interaction between devices).
There are various methods which can be used to program the
SET-DLCM. These are:- SET-DFP (faceplates), a SET-DHHP
(Daylux Hand Held Programmer) and the SET-DPCS (Daylux PC
Software).
The method used will determine what level of programming can be
achieved. The SET-DFP is the most basic means of programming
and the SET-DPCS is the most advanced.
MIN
MAX
MANUAL (ON OFF)
PRESENCE
ABSENCE
DAYLIGHT
DAYLIGHT / PRESENCE
DAYLIGHT / ABSENCE
DAYLIGHT / PRESENCE / DIMMING
DAYLIGHT / PRESENCE / SCENES /
DIMMING
MIN
MAX
KEY:
Daylight Link
Switch
Absence
Dimming
Scenes / Faceplate
Presence
MIN
MAX
Notes:
A ‘short press’ is less than half a second. ‘Press and hold’ is for
longer than half a second. *Raise and Lower will only function when
dimmable lighting is being controlled.
SWITCH FUNCTIONS TABLE
SHORT
PRESS
SW1
SW2
SW3
SW7
LIGHTS
ON
LIGHTS
OFF
SHORT
PRESS
PRESS
HOLD
PRESS
HOLD
INCREASE
LEVEL*
DECREASE
LEVEL*
TEST
ON
TEST
OFF
OVERRIDE
ON
OVERRIDE
OFF
SW6
EM TEST
ON
EM TEST
OFF
For >5s
RESTART
DSI/DALI
TOGGLE
>0.5s
STORE
SCENE
>5s
FACTORY
DEFAULTS
