Please install and adjust the machine according to the requirements of the manual.
It is very important for your safety and correct operation.
Unpacking
Unpack the carton and take out the bottom panel.
Open the top lid of washing machine and take out all the accessories.
Remove all the wrappers, including the polystyrene base.
You are advised to keep all the packaging for reuse, in case the machine is to be
transported again.
Installation and adjustment
Installing the bottom cover
Fixing clamp
Scissors
Bottom cover
The base
Positioning
The distance between the washing machine and the wall should be more than 50mm and the
maximum allowed angle of the shank base of the machine is 1 . The slanting or rough ground may
cause instability or the operation to stop. Please adjust it with the following methods:
Horizontal checking:
is in red circle or not. In red circle, it is horizontal.
Adjust the adjustable foot:
1.
and twist the adjustable foot.
2. Fasten the nut after adjustment.
3.
is not in red circle,
bubble is in red circle.
2
To fix bottom cover, first cut the clamps on the
cover and insert the cover in slots present at bottom
in the direction mentioned in the picture. Place two
screws at the bottom in the present slot to
permanently fix it.
How to use drainpipe
Water drainage
The drain hose should drain smoothly:
1. The height of the drain hose should be less
than 10cm, otherwise the drainage will not be
smooth and would need a long time to drain. The machine
may stop during working.
2. Do not step on or press the drain hose.
4. Purchase a proper hose, if you need an additional one.
Its diameter should not be less than 30mm and length should
not exceed 1.5m.
A B
3. Cut the drain hose, if it is too long. Cut the front end of the
hose slantingly to make drainage smooth.
How to change the direction of the drainpipe
1. Take off the drainpipe and its clip from the connector.
Put a soft mat on the floor and make the washing
machine front side down. Now, gently demount the
screws on the back cover with a screwdriver and take it
out. Demount one screw from the drainpipe connector
(on right side of the washing machine) and loosen it.
3. With proper force, take down the drainpipe gate stopper
from the left side of the washing machine. The drainpipe
gate stopper is fixed on washing machine base with
two clips. Please see the fixing type from the place of
back cover opening.
2. Extrude the drainpipe with proper force
and take out drainpipe hoop (on right of the
washing machine). Loosen the inner
drainpipe.
4. Pull the inner drainpipe to another side.
Please do not make any distortion in the
inner pipe; as per foregoing description,
fix inner drainpipe with a drainpipe hoop.
With one screw, fix drainpipe
connector
and install the drainpipe gate stopper to
another side. Make the washing machine
stand gently and fix the back cover with
a screw. Now, install the drainpipe and
drainpipe clip into the drainpipe connector.
Install drainpipe
Set drainpipe clip into the drainpipe to above 2-3cm (from the drainpipe end without pothook).
Now, install the drainpipe into the right drainpipe connector and fix the drainpipe
and drainpipe connector with the clip. After that, put the drainpipe clip on the cabinet.
Drainpipe hoop
Drainpipe gate stopper
Drainpipe connector
Drainpipe
Drainpipe clip
(Section sketch map for washing machine right side)
Section sketch map inside washing machine
Section sketch map for washing machine left side
,
If the additional drain hose is too long,
cut some at A or B point.
5
6
Loosen
Fasten
Adjustable
nut
Adjustable
foot
Low
High
Lift up the adjustable foot gently. Now loosen the adjustable nut
repeat the above procedure till the water
Set the machine flat and observe again. If the water bubble
Observe, if the water bubble in balancing apparatus
Before using
Before using
