DAVIS Wireless Temperature/Humidity Station Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 12

DAVIS Wireless Temperature/Humidity Station Скачать руководство пользователя страница 6

6

This confirms communication between your Temp/Hum Station and the console. If
you are not receiving the sensor readings on the console go the the next section, “No
Communication with Temp/Hum Station”.

3. Close the SIM Shelter cover. See page 4.

4. Go on to “Choosing a Location for the Temp/Hum Station” on page 7.

No Communication with Temp/Hum Station

1. First, verify that the console is powered and is not in Setup Mode. Exit Setup

Mode by pressing DONE and holding it for a moment.

2. On the Temp/Hum Station, check that the battery is properly installed.

3. Walk around the room with the console, standing for a few moments in various

locations to see if you are picking up signals. It may take up to three minutes to
acquire a signal, see your Vantage Pro2 Console manual for details on transmis-
sion.

4. If you don’t see readings no matter where you stand with the console, put the

transmitter on your Temp/Hum Station in TEST mode.

TEST mode

DIP switch #4 on the SIM (see illustration on page 4) is the TEST DIP-switch.
Switch it to the ON position using a ball-point pen or paper clip. This puts the trans-
mitter in

Test Mode.

An LED indicator light will flash each time the station trans-

mits:

• The LED will flash each time the transmitter broadcasts a signal, which should

be every 2.5 seconds.

If the LED does not flash, there may be a problem with the transmitter. See “Con-
tacting Davis Instruments” on Page 10.

If the LED flashes repeatedly but your console isn’t picking up a signal anywhere in
the room, it could be related to one of the following causes:

1. The DIP switches were not correctly set on the Temp/Hum Station.

Review “Setting the Transmitter ID” on page 4.

2. The ID was not correctly set on the console.

Review “Setting the Console Station ID on the Console” on page 5.

3. Reception is being disrupted by RF (radio frequency) interference.

4. There is a problem with the console or Temp/Hum station.

See “Contacting Davis Instruments” on page 10.

Note: Remember

to

set the Test DIP switch OFF

when you’re finished testing wireless transmission. If

it is left ON, the blinking LED will reduce battery life significantly.

«
...
4
5
6
7
8
...
»

Содержание Wireless Temperature/Humidity Station













Отзывы:

Нет отзывов