DAVIS Vantage Pro ISS Retrofit Kit Скачать руководство пользователя страница 24

Product Numbers: 6921, 6921C

Davis Instruments Part Number: 7395.132
Fan-Aspirated ISS Retrofit Kit
Rev. B (April 16, 2003)

This product complies with the essential protection requirements of the EC EMC Directve 89/336/EC. 
Copyright ©2003 Davis Instruments Corp. All rights reserved.

Vantage Pro is a registered trademark of Davis Instruments Corporation.

3465 Diablo Avenue, Hayward, CA 94545-2778 U.S.A.

510-732-9229 • Fax: 510-732-9188

E-mail: [email protected]  •  www.davisnet.com

FCC Part 15 Class B Registration Warning

This equipment has been tested and found to comply with the limits for a class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment generates, 
uses and can radiate radio frequency energy and, if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications. However, there is 
no guarantee that interference will not occur in a particular installation. 
If this equipment does cause harmful interference to radio or television reception, which can 
be determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to 

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved in writing by Davis Instruments may void 
the user’s authority to operate this equipment.

ISS2 SPARS RetroKit D011.fm  Page 24  Wednesday, April 23, 2003  11:26 AM

Содержание Vantage Pro ISS Retrofit Kit

























Отзывы: