DAVIS Envoy8X Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 48

DAVIS Envoy8X Скачать руководство пользователя страница 5

1

Wireless Repeater Overview

The Davis Wireless Repeater can be used with any Vantage Pro2 wireless station to
retransmit weather data to a Vantage Pro2 compatible receiver (Vantage Pro2 or Vantage
Vue console, Weather Envoy, Envoy8X, or Vantage Connect). It can be used to extend
the distance between one station and a receiver, or in conjunction with other repeaters to
create a flexible network of stations and repeaters.

Note: The repeater is fully compatible with Vantage Vue weather stations. Please refer to your

Vantage Vue

Console Manual

, Appendix C: Repeater Configuration, for specific Vantage Vue configuration

instructions. (The manual can be found on our web site at www.davisnet.com/support.) Please note that
the illustrations in this manual often depict multiple transmitters which are only supported in Vantage
Pro2 and Envoy.

Included Components and Hardware

The Wireless Repeater comes with the components and hardware shown in the following
illustration. Some of the hardware might not be used, depending on how the repeater is
installed.

3-Volt Lithium

Battery

8" Cable Ties

1/4" x 1-1/2"

Lag Screws

Repeater in Shelter

with Solar Panel

U-Bolts

1/4" Flat Washers

1/4" Lock Washers

1/4" Hex Nuts

«
...
3
4
5
6
7
...
»

Содержание Envoy8X

















































Отзывы:

Нет отзывов