manualshive.com logo in svg

DAVIS DriveRight, Руководство по установке

Поделиться
Скачать
DAVIS DriveRight Скачать руководство пользователя страница 13

 

12

 

F

 

RONT

 

 W

 

HEEL

 

 D

 

RIVE

 

NOTE:

 

Thinking ahead...Choose the in-board CV joint hub you want to use by looking at how you 
can mount the sensor and how in Step 5 you will route the wires into vehicle cabin . Con-

 

sider where feedthrus are and how you will make the connections in Step 6.

 

Select an in-board CV joint hub and install the magnet (22) in its mount (23) using 
the large tie wrap (24) as shown in Figure 16. Loosely cinch the large tie wrap 
around the CV joint, with the magnet mount oriented as shown, so you can adjust 
its final position after the sensor is installed. Do not overlap boot. Do not cinch tie 
wrap. Choose mounting locations for the sensor mounting bracket and support 
bracket on the transaxle/engine assembly (Figure 17). Do not mount the bracket on 
the vehicle chassis because of engine torque. Do not use fluid retaining bolts to 
retian the brackets.

 

Figure 14: Positioning the Sensor (Front Wheel Drive)

Figure 15: Determining Proper Clearances and Gap (Front Wheel Drive)

Figure 16: Installing the Magnet (Front Wheel Drive)

Содержание DriveRight


























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды