manualshive.com logo in svg

DAVIS DriveRight 8156GD, Руководство по установке

Поделиться
Скачать
DAVIS DriveRight 8156GD Скачать руководство пользователя страница 15

Connect the black ground wire from the adapter cable to chassis ground.

Use in-line butt splices to connect the blue wires with fuses to the green and 
yellow digital input cables.

Connect digital input 1 to the desired circuit, typically the brake light circuit.

Connect digital input 2 to the desired circuit, typically the headlight circuit.

Connect the adapter cable to the harness cable. 

❏

It is easiest to make the connection if you hold the harness cable 
connector by the connector housing and hold the adapter cable by the 
cable next to the connector.

❏

Push the two connectors together. The connector housing on the 
adapter cable slides back when you make the connection, allowing the 
cables to lock together.

1RWH

To disconnect the cables, hold the both cables by the housing and pull apart. The sliding 
housing on the adapter cable connector will release the lock and allow the cables to be 
separated.

3URFHGXUH,QVWDOOWKH'ULYH5LJKW&RQVROH

The DriveRight console can be mounted in a number of places, including the top 
of the dash, on the face of the dash, or on a sun visor. 

)DFHRI'DVKERDUG0RXQWLQJ2SWLRQV

Sliding

Connector

Housing

Adapter Cable

Harness Cable

To Connect Cables, 

Hold as Shown Here 

Mounting

Bracket

Double-Sided
Foam Tape

OR

Flat Head Self-Tapping Screw (2x)

Mounting

Bracket

07395.043 DR GD Inst Rev D Body D146.fm  Page 13  Monday, December 1, 2003  12:02 PM

Содержание DriveRight 8156GD

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды