manualshive.com logo in svg

DAVIS DriveRight 130AL, Руководство пользователя

Поделиться
Скачать
DAVIS DriveRight 130AL Скачать руководство пользователя страница 29

Page 27

• I can't turn my lamps off.

Make sure you are in the current readings screen when you hit 

"+"

 or 

"-"

. (See 

“Current Readings Screen” on page 11.)

• The lamps come on momentarily when I plug the unit in.

This is normal.

• When operating on batter power, the LCD segments are faint.

Battery power is low. Replace the battery. (See “Battery Operation” on page 25.)

• The BAT segment is on when the unit is plugged in.

The unit is not getting primary power.  Check the fuse in the power line.

• My buzzer is faint or not audible when the unit is operating on 

battery power.

This is normal.

• The display is blank even when plugged into the vehicle.

It is possible that the unit was in sleep mode (see “Battery Operation” on 
page 25) when you connected it to the car. Press 

MODE

 to “wake” the unit up. 

If this does not solve the problem, or if the unit goes into sleep mode when 
connected, consult the troubleshooting section in the Installation Guide.

• My DriveRight 130AL and my speedometer do not agree.

From the calibration screen, use the 

"+"

 and 

"-"

 keys to fine adjust the speed.

NOTE:

 The DriveRight 130AL responds to changes in speed faster than most 

speedometers.

• My speed is intermittently reading zero while driving.

This could be one of two things. First, make sure the speed sensor is within 3/
8”- 5/8” (10-16 mm) of the magnet. If it is, make sure the installed speed sen-
sor protrudes at least 

Ω

” from the bracket.

• My speed reads zero while driving.

There could be a number of things wrong. Make sure the DriveRight 130AL is 
plugged in. Make sure the DriveRight 130AL is calibrated. Make sure the 
speed sensor is within 3/8”-5/8” (10-16 mm) of the magnet. Make sure the 
unit is not running on battery power (see “Battery Operation” on page 25).  If 
it is check the fuse in the power line. If all of this fails to solve the problem, 
consult the trouble shooting section of your Installation Guide.

• The speed reading on the DriveRight 130AL agrees with my 

vehicle’s speedometer, but the distance reading on the Drive-
Right 130AL and my odometer differ (or vice versa).

First of all, make sure you follow the DriveRight 130AL calibration instruc-
tions (see “Calibrating the DriveRight 130AL” on page 8) carefully.  If you 
have calibrated correctly and the difference between the DriveRight 130AL’s 
reading and the vehicle’s reading is more than 1%, the error lies in the link 
between your vehicle’s odometer and speedometer.

Содержание DriveRight 130AL

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды