background image

DAVINCI GLIDERS / RHYTHM2

11

14. Packing your RHYTHM2

15. Maintenance and cleaning

Spread the RHYTHM2 completely out on the ground. Separate the lines to each side. The RHYTHM2 must 

be folded cell to cell to keep the plastic reinforcement at the leading edge lie flat on each other and don’t 

get bent. Try to pack your RHYTHM2 as loosely as the rucksack allows because every fold weakens the fabric.

Avoid packing the glider where it is wet or abrasive conditions(sand, asphalt pavement, concrete)

Cleaning should be carried out with only pure water. If the glider comes in contact with salt 

water, clean thoroughly with fresh water. Do not use solvents of any kind, as this may remove 

the protective coatings and destroy the fabric.

13. Landing

We recommend landing with trimmers to the normal slow position. Don’t use sharp turns or radical 

maneuvers.

When you are 1-2m over the ground, you should face into the wind and standing upright and ready to run. 

Finally, you may pull the brakes smoothly for minimizing vertical speed.

Don’t hit the ground by your overtake the glider. If you in windy condition, as soon as you touch the ground 

you have to turn around to face the glider and move towards it during full pulling break symmetrically.

Содержание RHYTHM 2

























Отзывы: