manualshive.com logo in svg

Datum Systems PSM-2100L, Руководство пользователя

Поделиться
Скачать
Datum Systems PSM-2100L Скачать руководство пользователя страница 11

L-Band IF Interface Preliminary Addendum

Page L-Band - 11

The following table lists the remote control packet commands that are new or modified in the PSM-2100L (L-Band Modem) by binary command number. This
table is only for PSM-2100L Units with software revisions “1.00” and above. The software version can be viewed at the unit front panel.

Table B-1

PSM-2100”L” Remote Control Packet Command Additions/Modifications for Software Rev “1.00”

Modem Function

Binary

Cmd

ASCII

Cmd

Write Value

Read Value

Mod CXR Frequency (MODIFIED,
now uses 5 bytes in binary)*

01h

MCF

950.000000MHz to 1650.000000MHz

Only if “Mod Cnvrter LO” = 0

950.000000MHz to 1650.000000MHz

Only if “Mod Cnvrter LO” = 0

Mod CXR Frequency (NEW MODE,
now uses 5 bytes in binary)*

01h

MCF

950.000000MHz to 1650.000000MHz Plus or

Minus “Mod Cnvrter LO” if not = 0

950.000000MHz to 1650.000000MHz Plus

or Minus “Mod Cnvrter LO” if not = 0

Mod CXR Offset Frequency
(MODIFIED Range)

02h

MOF

-750.000kHz to +750.000kHz

-750.000kHz to +750.000kHz

Mod Output Level (MODIFIED)

03h

MOL

+5.0dBm to -35.0dBm

+5.0dBm to -35.0dBm

Mod Spectrum (NEW)**

29h

MSP

0 = Normal, 1 = Inverted

0 = Normal, 1 = Inverted

Mod Cnvrter LO (NEW)

2Ah

MLO

Either 0, OR BUC LO frequency

(e.g. 4900.000000MHz)

Either 0, OR BUC LO frequency

(e.g. 4900.000000MHz)

Demod CXR Frequency
(MODIFIED, now 5 bytes in binary)*

41h

DCF

950.000000MHz to 1650.000000MHz

Only if “Demod Cnvrter LO” = 0

950.000000MHz to 1650.000000MHz

Only if “Demod Cnvrter LO” = 0

Demod CXR Frequency
(NEW MODE, 5 bytes in binary)*

41h

DCF

950.000000MHz to 1650.000000MHz Plus or

Minus “Demod Cnvrter LO” if not = 0

950.000000MHz to 1650.000000MHz Plus

or Minus “Demod Cnvrter LO” if not = 0

Demod CXR Offset Frequency
(MODIFIED Range)

42h

DOF

-Wide Sweep to +Wide Sweep

(Max. +/- 750 kHz)

-Wide Sweep to +Wide Sweep

(Max. +/- 750 kHz)

Demod Input Level (MODIFIED)

43h

DIL

Read Only

-20 to -105 dBm in 1 dB increments

Demod Wide Sweep Freq.
(MODIFIED Range)

56h

DWS

0.2kHz to 750.0kHz

0.2kHz to 750.0kHz

Demod Spectrum (NEW)**

69h

DSP

0 = Normal, 1 = Inverted

0 = Normal, 1 = Inverted

Demod Cnvrter LO (NEW)

6Ah

DLO

Either 0, OR LNB LO frequency

(e.g. 5150.000000MHz)

Either 0, OR LNB LO frequency

(e.g. 5150.000000MHz)

* See Section 2.1 for more detail on frequency settings
** The Mod and Demod “Spectrum” parameters should be set to “Normal” when Converter LO frequencies not zero are entered.

Содержание PSM-2100L












Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды