Datex-Ohmeda S/5 B-GAS Скачать руководство пользователя страница 32

Страница: 32 / 83

Datex-Ohmeda S/5 Anesthesia Monitor

Document No. 800 1005-1

2.2.9

Gas interface board

The Gas interface board, B-GAS is used for connecting an Airway Module to the Central Unit.
The board connects Airway Module signals to the module bus and supplies voltages from the

module bus to the Airway Module.
On the board there is a fuse (T4A) and some capacitors to regulate the power supply.

2.3

Connectors and signals

2.3.1

Module bus connector

Pin No

I/O

Signal

RESET RS485

-15 VDC

+15 VDIRTY

+15VDC

I/O

-DATA RS485

I/O

DATA RS485

Ground and Shield

-RESET RS485

n/c

Ground and Shield

+24/+32 VDIRTY Depends on power supply

Ground DIRTY

n/c

GASFR (not used)

CTSD (not used)

TXDD (not used)

RXDD (not used)

+5 VDC

+5 VDC DIRTY, for infrared lamps

For B-GAS CPU Mother Board connector, see CPU Bus Connector in the Central Unit Section.

Содержание S/5 B-GAS




















































































Результаты поиска

Содержание S/5 B-GAS

Отзывы:

Похожие инструкции для S/5 B-GAS

Бренды по названию

Популярные бренды

Datex-Ohmeda S/5 B-GAS, Техническое справочное руководство

Результаты поиска

Содержание S/5 B-GAS

Отзывы:

Похожие инструкции для S/5 B-GAS

Бренды по названию

Популярные бренды