background image

 

WM-10 Professional Wall Mount Kit for Datavideo Robotic Pan Tilt 

Head   

Introduction 

The WM-10 is a professional wall mount which is designed for Datavideo Robotic Pan 

Tilt Head PTR-10/PTR-10T and Datavideo PTZ camera series including PTC-150/PTC-

150T/PTC-200/PTC-200T. The WM-10 is made by 6061 Aluminum. Moreover, the 

WM-10 provides two bubble level meters for users to measure whether the PTR-10 

or PTR-10T is mounted horizontally. Please follow following steps for assembling the 

WM-10 wall mount. This user manual take PTR-10 as an example.   

Assembly Steps of the WM-10 

Please follow following steps for assembling the WM-10. 

 

How to install the WM-10 to the Wall   

 

Step 1. Please drill four holes according to the No.1 to No. 4 holes on the 

following diagram Figure 1. 

 

 

Step 2. Please fix the back plate(A) to the wall by screwing four screws with 

screw anchors according to the No.1 to No. 4 order.   

 

 

Step 3. After the back plate (A) of the WM-10 is fixed to the wall, please screw 

the No.5 and No.6 screws with nuts to the left-side plate(C) for connecting the 

left side plate(C) to the back plate(A) of the WM-10 according to following 

diagram Figure 1.   

 

 

 

Содержание WM-10





















Отзывы: