background image

 

Disposal 

For EU Customers only - WEEE Marking 
This symbol on the product or on its packaging indicates that 
this  product  must  not  be  disposed  of  with  your  other 
household waste. Instead, it is your responsibility to dispose of 
your  waste  equipment  by  handing  it  over  to  a  designated 
collection  point  for  the  recycling  of  waste  electrical  and 
electronic equipment. The separate collection and recycling of 
your  waste  equipment  at  the  time  of  disposal  will  help  to 
conserve natural resources and ensure that it is recycled in a 

manner  that  protects  human  health  and  the  environment.  For  more  information 
about where you can drop off your waste equipment for recycling, please contact your 
local  city  office,  your  household  waste  disposal  service  or  the  shop  where  you 
purchased the product. 

CE Marking is the symbol as shown on the left of this page. The 
letters "CE" are the abbreviation of French phrase "Conformité 
Européene"  which  literally  means  "European  Conformity".  The 
term initially used was "EC Mark" and it was officially replaced by 
"CE Marking" in the Directive 93/68/EEC in 1993. "CE Marking" is 

now used in all EU official documents. 
 
 

 
 

 

Содержание WM-10





















Отзывы: