Install Hard Drive into tray
NOTE: Please reference the documentation that came with your
hard drive for diagrams which show the SCSI pin location(s) on
your drive.
1. Open your DataTrans tray by gently pulling the “open” tab on
the cover of the tray away from the tray side and then slide
the cover toward the rear of the tray. You will find the tab on
the front left corner of the tray cover.
2. Inside your tray you will find several sets of cabling, including
a four-pin power connector, a 68pin HDD controller connector,
a set of 5 wires for SCSI ID, and a set of two wires for the
Drive Activity LED (See Figure 4).
3. Referencing the manual that came with your drive, plug the
SCSI ID cables into the back of the drive. Figure 5 provides a
nomenclature color diagram for the SCSI ID cabling inside
the tray. Figure 6 provides a sample jumper configuration
4. If you desire, plug the Drive Activity Cable into the appropriate
connector on your drive.
5. Plug the four-pin power connector and the 68pin HDD controller
connector into the drive.
6. Mount the drive into the tray using the four screws provided.
7. Replace the cover by following the reverse procedure for
removing it in step 1.
Install Tray into Frame
1. Prior to replacing the cover on your enclosure, be sure to set
your SCSI ID using the rotary switch located on the bottom
right of the tray (Figure 7). Do not confuse the SCSI ID cables
with the Drive Activity Cable, which is a paired cable on the
same terminal which consists of one Black wire and one Red
wire (Red is signal, Black is ground).
2. Insert a key from the set provided into your tray lock, and turn
the key counter clockwise to lock the tray - the drive is now
ready to receive power, and should power up normally when
your system is on.
Replace Enclosure Cover
1. Following the documentation provided by the manufacturer of
your enclosure, replace the cover of the enclosure.
Figure 4
Wiring (Inside Tray)
Copyright 1999 by DataStor, Inc. All rights reserved. No part of this document may be reproduced in any form without prior written consent from DataStor. The information and specifications in this document are subject to change without
notice. Changes to this document are incorporated in new versions. DataStor, and the DataStor logo are reqistered trademarks of DataStor, Inc. Other trademarks used herein are the property of their respective owners. This document
was printed in the United States Of America.
Installation Guide - DataTrans 68 pin Plastic Removable Tray&Frame, Rev 1.0 - December 1998 - P/N DT51UWS-P
DataStor, 12601 Monarch Street, Garden Grove, CA, 92841-3918
Phone (800) 777-6621 / Fax: (714)833-9600 / Web Site: www.dstor.com
Figure 5
Yellow
Green
Red
Brown
Figure 7
SCSI Switch
Back of Tray
Green
Green
Green
Green
Green
YYYYYellow
ellow
ellow
ellow
ellow
Red
Red
Red
Red
Red
Brown
Brown
Brown
Brown
Brown
=
=
=
=
ID 8 signal
ID 8 signal
ID 8 signal
ID 8 signal
ID 8 signal
ID 4 signal
ID 4 signal
ID 4 signal
ID 4 signal
ID 4 signal
ID 2 signal
ID 2 signal
ID 2 signal
ID 2 signal
ID 2 signal
ID 1 signal
ID 1 signal
ID 1 signal
ID 1 signal
ID 1 signal
SCSI Signal Chart
SCSI Signal Chart
SCSI Signal Chart
SCSI Signal Chart
SCSI Signal Chart
012
34
56
789AB
C
DEF
68 pin HDD
Controller Connector
Power
Connector
SCSI
ID Cables
HDD
Activity
Cable
(Jumper set A3)
(Jumper set A3)
(Jumper set A3)
(Jumper set A3)
(Jumper set A3)
(Jumper set A2)
(Jumper set A2)
(Jumper set A2)
(Jumper set A2)
(Jumper set A2)
(Jumper set A1)
(Jumper set A1)
(Jumper set A1)
(Jumper set A1)
(Jumper set A1)
(Jumper set A0)
(Jumper set A0)
(Jumper set A0)
(Jumper set A0)
(Jumper set A0)
Figure 6
Sample SCSI ID
Jumper Configuration
Green
A3 A2 A1 A0
Yellow
Empty
Empty
Red
Brown