background image

DI-789 Hardware Manual

Installation

8

Installing a DI-789 to a Synchronous chain on a distributed network without 
a DHCP server where static IP address are individually assigned

Installation of an Ethernet Synchronous chain connected to a distributed network that does not have a DHCP server or 
where the DHCP server is turned off requires you to set a static IP to the device after installation to drastically reduce 
the amount of time it takes for the TCP/IP Manager to find the device.

Note: In the illustration above, the Ethernet Synchronous Chain could be located anywhere in the network. Also, the 
Hubs could instead be routers with DHCP turned off (i.e., a static IP assigned network). Contact your system admin-
istrator for details about your network.

1.

Have the system administrator designate an IP address for your device(s).

2.

Install W

IN

D

AQ

 software (see “Installing Software” on page 10) entering the device’s MAC address at Step 13.

3.

Run the TCP/IP Manager software (default location is 

Start > Programs > WINDAQ > IP Manager

).

4.

Connect the device to your network (see “Connecting the Device” on page 11).

5.

Power the device (see “Applying Power to the Instrument” on page 12).

6.

In the 

TCP/IP Manager main window

select the device

 you have installed. 

7.

Select the 

Change IP Address

 drop down command. 

CAT-5 Cable

100M Max

Your PC

Hub

CAT-5 Cable

100M Max

Hub

PC

PC

More Nodes 

As Needed

Ethernet Synchronous Chain

(DI-72x/730/78x)

Содержание Ethernet DI-789























Отзывы: