Datalogic ENC-58 PROG Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 38

Datalogic ENC-58 PROG Скачать руководство пользователя страница 29

ENC58 PROG

24

at which the 0 pulse is located in the 360° revolution of the encoder
shaft is displayed.
Default = 0 (min. value = 0; max. value = 262143)

WARNING
Please check the position of the 0 pulse and set it if necessary
whenever you set a new resolution next to the

Resolution

parameter

or reverse the counting direction.

NOTE
The width of the 0 pulse can be set next to the

Z pulse width

parameter. Two options are available: 90° and 180°.
Please note that the 0 pulse having a width of 90 electrical degrees
is synchronised with A and B pulses, while the 0 pulse having a width
of 180 electrical degrees is synchronised with A pulse.
For further information please refer to page 20.

NOTE
It is possible to set the 0 pulse position also by either sending a
signal via PLC or other controller through the dedicated input -see
the section “4.8 Index pulse setting input” on page 9-; or by pressing
the external button located in the rear side of the encoder enclosure -
see the section “4.11 Index pulse setting external button (Figure 1)”
on page 12.

«
...
27
28
29
30
31
...
»

Содержание ENC-58 PROG







































Отзывы:

Нет отзывов