Datalogic AREX 401 Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 148

background image

TECHNICAL SUPPORT

88

AREX™ 401

TROUBLESHOOTING

If a problem occurs during operation, first check the following troubleshooting. If you

cannot fix the problem, contact Datalogic Customer Service (see “Technical Support” on

Service Interface

The laser marker is equipped with a Service Interface integrated in

Lighter™ Laser Con-

figuration - Service

useful for service purpose.

The Service Interface provide the following information:

Laser marker serial number

Shows the FW and HW revision (separated by dot) installed in
the Laser Control Board
Counter of the laser marker working hours expressed in
hours and minutes

Shows the CPU temperature of the Laser Control Board

Shows the temperature measured by BOARD#1 sensor of the
control rack
Shows the temperature measured by BOARD#2 sensor of the
control rack

Shows the internal temperature of the Scan Head

DESCRIPTION

This counter is incremented every time the system tempera-
ture is out of the operating temperature range
This counter is incremented every time the scan head tem-
perature is out of the operating temperature range
This counter is incremented every time the service interface
detect a MMC error

Counter of the safety functions events. The safety functions
events counter is incremented every time the INTERLOCK or
LASER_STOP safety function are activated

SYSTEM INFO

INFO TYPE

DESCRIPTION

Serial Number

FW revision

System Working Hours

CPU Temperature

BOARD#1 Temperature

BOARD#2 Temperature

Scan Head Temperature

ERROR TYPE

System Temperature error

Scan Head Temperature error

Service Interface error

SAFETY INFO

INFO TYPE

DESCRIPTION

Safety relay switching

«
...
94
95
96
97
98
...
»

Содержание AREX 401





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для AREX 401

Бренд: Valeport Страницы: 25

Бренд: 3nh Страницы: 10

Бренд: MadMan Страницы: 37

Бренд: MADDALENA Страницы: 5

Бренд: Omega Страницы: 74

Бренд: Omega Страницы: 24

Бренд: Technoline Страницы: 1

Бренд: Interacoustics Страницы: 54

Бренд: PCB Piezotronics Страницы: 10

Бренд: NARDA Страницы: 240

Бренд: Behringer Страницы: 2

Бренд: Selecta Страницы: 16

Бренд: LaserLiner Страницы: 64

Бренд: Topcon Страницы: 2

Peak Flow Meter

Бренд: TruZone Страницы: 20

Бренд: Protimeter Страницы: 3

Бренд: PKP Страницы: 28

Бренд: Tempo Communications Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды