Datalogic AREX 401 Скачать руководство пользователя страница 89

Страница: 89 / 148

REMOTE START FOOT SWITCH

USER MANUAL

REMOTE START FOOT SWITCH

This accessory is used to provide the

START_MARKING

signal to the laser marker when

the pedal is pressed by the operator.

Figure 65: Remote Start Foot Switch (ordering no: 985350035)

I/O INTERFACE

Dedicated to on-site quick and easy termination, PLC interfacing, System Test, I/O trou-
bleshooting, etc. The DB25 Pass-through Command Box connector allows the integrator
to use the interface as a I/O test tool on previously installed products.

•

I/O Monitoring LED

•

Easy assembly thanks to screw down termination

•

Dry contact outputs

•

Dry contact inputs

•

DIN rail mounting enclosure

Figure 66: I/O interface (ordering no: 985330032)

NOTE: Refer to Remote Start Foot Switch instruction manual for more
information.

NOTE: Refer to I/O Interface instruction manual for more information.

Содержание AREX 401





















































































































































Результаты поиска

Содержание AREX 401

Отзывы:

Похожие инструкции для AREX 401

Бренды по названию

Популярные бренды

Datalogic AREX 401, Руководство пользователя

Результаты поиска

Содержание AREX 401

Отзывы:

Похожие инструкции для AREX 401

Бренды по названию

Популярные бренды