DataDirect Networks EF3015 Скачать руководство пользователя | Manualshive

Страница: 13 / 59

background image

Installation

E F 3 0 1 5 S e t u p G u i d e ( R e v A )

13

2.3

AC PSU

Power cord connect

Figure 3. AC PSU

Controller and drive enclosures configured with switchless PSUs rely on the power cord for
power cycling. Connecting the cord from the PSU power cord connector

to the

appropriate power source facilitates power on; whereas disconnecting the cord from the
power source facilitates power off.

To power on the system:

1.

Plug the power cord into the power cord connector on the back of the drive enclosure.
Plug the other end of the power cord into the rack power source (see

and

). Wait several seconds to allow the disks to spin up.

Repeat this sequence for each switchless PSU within each drive enclosure.

2.

Plug the power cord into the power cord connector on the back of the controller
enclosure. Plug the other end of the power cord into the rack power source (see

).

Repeat the sequence for the controller enclosure’s other switchless PSU.

Power supply
module

Rack power
source

Figure 4. AC Power Cord

To power off the system:

1.

Stop all I/O from hosts to the system.

2.

Shut down both controllers using

either

method described below:

«
...
11
12
13
14
15
...
»

Содержание EF3015




























































Отзывы:

Нет отзывов

Похожие инструкции для EF3015

Бренд: SCC Страницы: 47

Бренд: Argus Страницы: 24

Бренд: Sonnet Страницы: 8

BFC-SDO-150-KKXBR-RP

Бренд: BitFenix Страницы: 15

SuperSpeed 42636

Бренд: DeLOCK Страницы: 16

Бренд: L-Acoustics Страницы: 192

Бренд: Icy Box Страницы: 16

Бренд: Icy Box Страницы: 16

Бренд: FSP Technology Страницы: 16

Бренд: FSP Technology Страницы: 20

Бренд: ATX Страницы: 14

Бренд: Edge Страницы: 12

Бренд: Pulsar Страницы: 4

Бренд: E-Tech Страницы: 15

Бренд: Aero Страницы: 2

Бренд: IBM Страницы: 300

Бренд: Fantec Страницы: 15

NexStar NST-D100UFS

Бренд: Vantec Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды