DataDirect Networks EF3015 Скачать руководство пользователя страница 11

Страница: 11 / 59

EF3015 Setup Guide (Rev A)

Installation

2.1

Installation Checklist

Figure 2

outlines the steps required to install the enclosures, and initially configure and

provision the storage system. To ensure successful installation, perform the tasks in the
order presented.

Additional installation notes:

• Controller modules within the same enclosure must be of the same type.

• For optimal performance, do not mix 6Gb and 3Gb disk drives within the enclosure.

Figure 2. Installation Checklist

Step

Task

Where to find procedure

Install the controller enclosure and
optional drive enclosures in the rack, and
attach ear caps.

See the rack-mount bracket kit installation
instructions pertaining to your enclosure.

Connect power cords.

See the installation sheet for your EF3015 controller
enclosure.

Install required host software.

See

3.1 "Host System Requirements"

page

4. Connect

hosts.

See

3.3 "Connecting the Enclosure to Hosts"

on page

Connect remote management hosts.

See

3.6 "Connecting a Management Host on

the Network"

on page

Obtain IP values and set network port IP
properties on the controller enclosure.

See

3.9 "Obtaining IP Values"

on page

For USB CLI port and cable use, see Appendix

Also see the ship kit CD.

Perform initial configuration tasks

a. RAIDar is introduced in

4.1 "Accessing RAIDar"

on page

. See the RAIDar user guide or

online help for additional information.

•

See “Getting Started” in the EF3015 RAIDar User
Guide.

•

Initially configure and provision the
system using RAIDar.

See “Configuring the System” and “Provisioning the
System” topics in the RAIDar user guide or online
help.

Содержание EF3015




























































Результаты поиска

Содержание EF3015

Отзывы:

DataDirect Networks EF3015, Руководство по установке, Страница: 11 / 59

Результаты поиска

Содержание EF3015

Отзывы: