manualshive.com logo in svg

Data Industrial 200 Series, Руководство пользователя, Страница: 4 / 10

Поделиться
Скачать
Data Industrial 200 Series Скачать руководство пользователя страница 4

Data Industrial 

Plastic Tee Type Flow Sensor

 Manual

4

Electrical Installation "Magnetic" sensors

The magnetic sensor has a custom wire connector that connects to the series 1400 monitor only. The cable

may be extended up to 100 feet from the sensor. If extension cables are needed they may be ordered from

Data Industrial.

Electrical Installation (FM Sensors)

The Series 200 Sensor is approved, as an entity, as Intrinsically Safe when installed in conformance with Data

Industrial installation drawings 06-480-001 or 06-480-002 (samples shown on Page 5) as specified on the blue

label identifying an intrinsically safe sensor.

Entity approval implies that only the sensor is approved as intrinsically safe. Unless power supplies, equipment,

and instruments connected to the sensor are each rated either explosion-proof or intrinsically safe, these

devices cannot be installed in a hazardous area.  The referenced installation drawing shows such apparatus

located in a non-hazardous location.  Proper interfacing between the hazardous and non-hazardous areas must

be provided.  It is of absolute importance that this interface be constructed and that all wiring be performed by

qualified contractors.  To ensure the Intrinsic Safety of the installation, the connection of the intrinsically safe

sensor to instruments and or power supplies must take place using an approved intrinsically safe barrier located

in a non-hazardous area.  These barriers, listed below, are readily available from various suppliers.

Manufacturer:

Barrier:

Crouse-Hinds  Spec 504

Cat No. SB19140M0715

Measurement Technology Ltd.

MTL 715+ 15 V

R Stahl Intrinspak

9001/01-158-150-10

Cable Length

Part #

5’

7101

10’

7108

20’

7102

50’

7109

Содержание 200 Series











Отзывы:

Нет отзывов