DAS MSENS-GY Скачать руководство пользователя

Страница: 22 / 23

3-axis accelerometer & 3-axis gyro sensor

MSENS-GY

User’s manual

WARNING: Shock hazard - Do Not Open.

Mains Plug or Direct plug-in adapter is used as disconnect device and it should remain readily operable

during

intended use. In order to disconnect the apparatus from the mains completely, the Mains Plug or Direct

plug-in adapter should be disconnected from the mains socket outlet completely.

WARNING: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning lash with arrowhead symbol, within

an equilateral triangle, is intended to alert the user

to the presence of uninsulated "dangerous voltage"

within the product's enclosure that may be of

suficient magnitude to constitute a risk of electric

shock to persons.

Tlie exclamation point within an equilateral triangle

is intended to alert tlie user to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

appliance,

FCC Warnings

WARNING: Changes or modiications to this unit not expressly

approved by the party responsible for compliance could void the

user's authoity to operate the equipment.

NOTE: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Pat 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different rom

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Содержание MSENS-GY
























Результаты поиска

Содержание MSENS-GY

Отзывы:

Похожие инструкции для MSENS-GY

Бренды по названию

Популярные бренды

DAS MSENS-GY, Руководство пользователя

Результаты поиска

Содержание MSENS-GY

Отзывы:

Похожие инструкции для MSENS-GY

Бренды по названию

Популярные бренды