Microtubes 200
Front Panel Features
INPUT
: Use this jack to connect your instrument via a standard
¼” mono cable.
MICROTUBES
: Use the Microtubes B3K® Engine to add natural
compression, organic harmonic enhancement, and saturation
ranging from mild overdrive to high gain bass rage. The Micro-
tubes B3K® Engine operates before the 4 band EQ section (so
you can use the EQ for additional tone shaping).
DRIVE
: This knob controls the amount of distortion that the
Microtubes B3K® Engine will deliver. It will change from a soft
warm overdrive to a massive modern distortion sound.
BLEND
: Use this knob to mix between the Clean signal and the
Distortion signal (Microtubes B3K® Engine).
BASS
: +-12dB at 80Hz. Use this knob to change the low-end
content of the signal.
LOW MIDS
: +-12dB at 1kHz. This knob controls the low mid
content of the signal.
HIGH MIDS
: +-12dB at 3kHz. This knob controls the high mid
content of the signal.
TREBLE
: +-12dB at 5kHz. Use this knob to change the high
content of the signal.
MASTER/MUTE
: Use this knob to control the overall volume of
the amplifier. Use this push knob button to mute the amplifier.
Rear Panel
SPEAKER OUTPUT
: Use this connector to connect the amplifi
-
er to your cabinet. This Speakon combo jack allows for either
Speakon or ¼” speaker cable operation.
WARNING
: Do not use an instrument cable with this jack.
Using an instrument cable can damage your amplifier.
Minimum load 3Ω.
GROUND LIFT
: Use this control to lift the ground of the DI XLR
output. If you are experiencing ground noise in your DI signal
try changing the setting of this control.
DI OUTPUT
: Use this connector to send your bypass signal to
the console, mic preamp, interface, etc. The DI OUTPUT delivers
only the bypass DI signal.
HEADPHONE OUTPUT:
Connect your Headphones and enjoy
the analog cabinet emulation.
AUX IN:
Use this connector to play music from your laptop,
phone, MP3 player, etc. This input is routed only to the
headphone output.
AC SOCKET
: Use this connector to feed electric power to the
amplifier. 100 - 230 VAC, 50-60Hz.
AC POWER ON/OFF
: Use this Switch to release the audio
energy from your bass.
Warning
· There are no user-serviceable parts inside the amplifier. Do
not open the amp.
· Never use the amp in a high moisture environment or near
liquids.
· The Microtubes 200 can deliver more than 100 dB of power.
Exposure to this level of sound can damage your hearing.
Always use proper hearing protection when exposed.
· The Microtubes 200 can deliver more than 200 watts. Be sure
that your speaker cabinet is able to deliver that power.
· Do not cover the vent holes. The fan and vent holes are part of
the cooling system of the amp. Covering the vent holes can
lead to overheating and damage to the amplifier.
· Do not use an instrument cable as speaker cable. An
instrument cable is not designed to deliver the type of power
sent from the amplifier to the speaker.
Specifications
Input Impedance
: 2.2MΩ
Load Impedance
: 3Ω Minimum
Aux In Input Impedance
: 10kΩ
Power Output
: 200 W RMS @ 4Ω @ 1 % THD+N, 1 kHz sine
100 W RMS @ 8Ω @ 1 % THD+N, 1 kHz sine
Maximum Power Consumption
: approx. 250VA
AC Input Power
: 100-120/210-250 VAC
Cycles
: 50/60 Hz
Dimensions Unpacked
: Width 150 mm (5.9 in) Height 52
mm (2.04 in) Depth 157 mm (6.18 in) Weight 965 g (2.12 lb)
Dimensions packed:
Width 240 mm (9.45 in) Height 85
mm (3.35 in) Depth 190 mm (7.5 in) Weight 1.4 kg (3.1 lb
)
Built and Engineered in Helsinki, Finland. (00358) 504 757005
Warranty
Please register for your warranty at http://mypedal.darkglass.com.
The Microtubes 200 is under warranty to the original owner for a
period of two years against manufacturing defects in the country
where the product was originally purchased.
If you experience a problem with the unit, please contact
[email protected] to receive a Return Authorization
number or for information on the nearest authorized repair
center. A copy of your original receipt must be included with all
warranty repairs. You are responsible for all shipping charges.
The unit must be shipped to us freight prepaid. We will return the
unit freight collect. Darkglass Electronics Oy is not responsible for
shipping damage either to or from our service center. Claims
must be filed with the carrier. For repairs please contact your local
dealer or distributor for your country’s specific warranty period
and repair procedures.
Darkglass®, Microtubes® and B3K® are registered trademarks of
Darkglass Electronics Oy.
Содержание Microtubes 200
Страница 1: ...OWNER S MANUAL ...
Страница 8: ......