14,2 %
2
18,1 %
6. Control Modes
You can control the device manually or with an IR remote control.
The IR remote control is supplied with the SC-5.2 Source Control
(D1540). Refer to the user manual of the SC-5.2 Source Control
(D1540) for the operation of the IR remote control.
14. Disposal
Dispose of this product by handing it to the respective
collection point for recycling of electrical and electronic
equipment. Do not dispose of with the household waste.
15. Approval
Check the respective product page on the website
of Highlite International (
) for an
available declaration of conformity.
© 2024 DAP. All rights reserved.
No part of this document may be copied, published or otherwise
reproduced without the prior written consent of Highlite International.
Design and product specications are subject to change without prior
notice.
For the latest version of this document and other language versions,
please visit our website
.
Highlite International B.V. • Vestastraat 2 • 6468 EX • Kerkrade • the Netherlands
SC-WP1 Wall Panel Black D1541 / White D1542
12. Troubleshooting
The device does not
function at all
Make sure that the CAT5/CAT6 cable is
rmly connected to the device.
Make sure that the SC-5.2 Source Control
is connected to the power supply and
switched on.
Make sure that the CAT5/CAT6 cable is
not damaged.
No sound
Increase the volume.
The device does not
respond to the remo-
te control
Make sure that there is a clear line of sight
between the remote control and the IR
sensor.
Change the battery in the remote control.
User Manual
Press one of the
source selection buttons (06)
to select a connec-
ted source device (Sources 1–4 or Local). The
LED indicator (07)
for
the respective source lights up.
Note:
The 5th source connected via the wall panel (Local) can be
selected only from the wall panel.
7. Source Selection
Turn the
volume control (02)
clockwise to increase the output
level. The 8
volume LED indicators (01)
light up one after the other
from left to right with the increase of the volume.
Turn the
volume control (02)
counterclockwise to decrease the
output level. The 8
volume LED indicators (01)
turn off one after the
other from right to left with the decrease of the volume.
10. Mute
Press the
volume control (02)
to mute the output.
Press the
volume control (02)
again to clear the mute status. The
volume returns to the last setting.
Press the
line/phone selection button (04)
to switch between line
or phone input.
8. Local Input Selection
Attention
The device is powered from the connected SC-5.2 Sour-
ce Control (D1540) via the connected CAT5/CAT6 cable.
Attention
Install all cables before mounting the device.
5. Installation
The SC-WP1 can be installed in a standard 1-gang wall box.
1
Attach the
wall-box mounting frame (B)
to the wall box
with the
2 short screws (F)
.
2
Insert the CAT5/CAT6 cables into the
RJ45 connectors (09)
to connect the device to the SC-5.2 Source Control (D1540).
3
Attach the
wall panel (A)
to the
wall-box mounting
frame (B)
with the
2 long screws (E)
.
4
Remove the tissue tape from the backside of the
front
plate (C )
..
5
Carefully place the
front plate
(C )
on the
wall panel (A)
.
Make sure that the openings t around the buttons.
6
Press rmly the
front plate (C )
to the
wall panel (A)
to
attach it.
7
Fit the
turn knob (D)
on the rotary encoder of the volume
control.
1
3
5
7
2
11. Remote Control
The IR remote control is supplied with the SC-5.2 Source Control
(D1540). Refer to the user manual of the SC-5.2 Source Control
(D1540) for more information.
Make sure that there is a clear line of sight between the remote
control and the
IR sensor (05)
.
ZONE
B
D
A
C
VOLUME CONTROL
SOURCE
2
3
4
1
1
Mute
Volume –
4
Source
A
D
Zone
Press to mute/unmute the output
Press to increase the volume
Press to decrease the volume
Press to select a source
No function
9. Adjusting the Volume
The device has an innite rotary encoder with an integrated push
switch to control the volume at the output.
Clean the device with a soft, lint-free cloth.
The device does not contain user-serviceable parts. Do not open
the device and do not modify the device.
Attention
Do not immerse the device in liquid. Do not use alcohol
or solvents to clean the device.
13. Maintenance