Dantel B18-04649-01 Скачать руководство пользователя страница 11

Страница: 11 / 14

04649-1098 <90-00194>

AGE

TECHNICAL SPECIFICATIONS

DESCRIPTION

B18-04649-02 SHELF (FULLY EQUIPPED)

Input Voltage

Input Current

Heat Dissipation
Operating Temperature Range

Physical Dimensions

19" Configuration
23" Configuration

Mounting Holes

19" Configuration
23" Configuration

Weight

4003C LINE AMPLIFIER (PER MODULE)

Terminating Impedance

Flat Gain/Loss
Deviation from Gain Setting

Output Level

Harmonic Distortion
Equalized Gain

Frequency Response Deviation

Delay Distortion
Crosstalk

Loss Between Channels

Loss Between Adjacent Units
Noise

Simplex Current

Tone Loopback

Threshold

Signal-to-Guard Ratio

Frequency
Operating Times

Initiate

Release

Local DC Loopback

Levels

Input Voltage
Input Current

Operating Temperature Range

Weight
Physical Dimensions

VALUE

-22 to -56 VDC

160 mA (min.); 335 mA (max.)

19.4 (+ 4003C min) (min); 30.6 (+ 4003C max) Btu/Hr (max)
0° to 55° C.

19" x 8.5" x 1.73"
23" x 8.5" x 1.73"

18.3" on center
22.3" on center

7.0 lbs. (4.9 lbs. empty)

1200, 600, or 150 ohms, balanced (switch selectable; all ports)

-24 to +24dB in 0.1 dB increments (switch selectable)
+0.25dB max. @ 1KHz

+15dBm max.

< 1% @ +15dBm
0 to 7.75dB in 0.25dB increments (switch selectable) (1K to 3KHz)

+1.0dB @ 1KHz

< 125 uS @ 1KHz

85dB min. @ 1KHz; 75dB min. @ 3KHz

90dB min. @ 1KHz; 85dB min. @ 3KHz
15dBrnC max. @ max. gain

120mA max. w/ 5mA max. unbalance

-18dBm w/ no gain (varies w/ receive channel gain or loss)

3dB min.

1 of 11; prescription set; center stabi0.2%; 75Hz bandwidth

1.4 seconds max.; (loopback after removal of tone)

0.7 seconds max.; (release during two-tone burst)
Ground to operate; 25mA current

+16dB, +9dB, -16dB, or -23dB switch selectable

-22 to -56 VDC
25mA min. to 65mA max.

-7° to 54° C.

16 ounces
1.4" x 6.0" x 5.6"

CONTINUED

. . .

Содержание B18-04649-01















Результаты поиска

Содержание B18-04649-01

Отзывы:

Бренды по названию

Популярные бренды

Dantel B18-04649-01, Руководство по установке и эксплуатации

Результаты поиска

Содержание B18-04649-01

Отзывы:

Бренды по названию

Популярные бренды