Dantel 49018 Скачать руководство пользователя страница 6

P

AGE

 6

49018-0697 <90-00089>

Clearing

The 49018 can be cleared internally or externally. When

strapped for internal clearing, the digit counter is restored three

seconds after a complete code is received, whether it is valid or

not. When strapped for external clearing, the busy circuit and

the digit counter are restored by a “Power-up Clear”, a “Reset”

input, or by internal decoding a “*”, “#”, or “C” BCD input,

depending on strapping.

Internal Clearing:

 When the  reset strap is IN, the interdigit

timer and reset circuit clears the entire station decoder three

seconds after the last digit is entered, or if three seconds pass

between digits. If the reset strap is OUT, the circuit wil not reset

after the last digit, but will reset if three seconds pass between

digits.

External Clearing:

 Three modes external clearing can be used

to clear or reset the 49018 subassembly:

A reset (ground) is provided from the station or PABX/Trunk

Interface Module (44022 or 44023) at P2-8 or a “Power-up

Clear” at P2-9.

The second mode is provided when the “#” or “*” BCD out-

puts of the supervisory decoder are strapped to the clear and

set outputs. Normally, the “#” is used to set the busy latch

and the “*” will clear the busy latch. This function can be set

to reverse the busy latch operation. The busy latch, when set,

provides a ground at P2-7 and applies a reset pulse through

the busy reset pulse circuit to clear the 49018 and prepare it

to accept the next address. The busy latch remains set until

it is cleared by the xternal reset, “Power-up Clear”, or an

internal BCD output from the supervisory decoder.

The third mode can be used when the “A” and “C” BCD codes

are strapped IN and perform the same functions as described

for the “#” and “*” BCD supervisory decoder outputs.

Power-up Busy

A power-up busy input at P2-12 is provided to set the busy latch

when the power-up signal from the 44020 DTMF Decoder

Module is received. The busy latch may be cleared by external or

internal sources as described above.

Clear Output

A clear output (ground) is applied to the 44022 or 44023 inter-

face modules using P2-10 each time the 49018 is cleared.

Toll Restriction Outputs

A toll restriction output is provided whenever a “0” or “1” BCD

signal is decoded by the supervisory decoder. The “0” or “1”

outputs do not require a reset code. They are applied through

respective buffer drivers at P2-5 or P2-6 to an external device

when toll restriction to a public telephone is desired.

CIRCUIT DESCRIPTION

Содержание 49018















Отзывы: