DanPumps S-IP Скачать руководство пользователя страница 3

 

 

 

4. Technical specification. 

 

  S-IP and S-MP pumps are assembled with a 3-phased motor. Version 2-pol or 4-pol. 

  50 or 60 Hz after choice. See motor label for accurate motor information on your pump. 

  230/400 or 400/690 after choice. See motor label for accurate motor information on your pump.  

  Motor space heater* 1x230vac. 50watt to 100watt. Have to be protected with an extern fuse. 

  Svend Höyer electric motors are type approved by BV, GL and ABS (design approval). 

  Svend Höyer electric motors are CE marked according to the Low Voltage Directive 2006/95/EC. 

  PTC resistance*:  200-250ohm at 20ºC.  (U = 7,5V max).  

  Thermistor. On/off. 135ºc. 

  Ambient temperature: up to max. 40ºC.  

  Media temperature: 5ºC to 100ºC 

  Flange according EN1092-1 

  Pump is based on design according ISO 2858. 

  Pump Standard surface treatment: Blue RAL 5010. C5M.  

 

*

 Only if it is built-in into the motor. 

 

 

 

 

Motor protection. 

 

Degree of protection is standard IP55, and insulation class is F. Tested to standard IEC 60034-2-1.  

The IE2 class motor has standard tropical windings.  

The IE3 class motor has tropical windings as an option.  

   

 

 

 

Pump material

 

 

    

Pump materiale as standard. 

Items 

S-IP 

S-MP 

Motor < 4 kw. 

Alu. 

Alu. 

Motor > 4 kw. 

Cast Iron 

Cast Iron 

Motor bracket 

Cast Iron 

Cast Iron 

Back plate 

Cast Iron 

Bronze RG10 

Mech Seal 

SiC/C-NITRIL 

SiC/C-NITRIL 

Pump shaft 

AISI 329 

AISI 329 

Impeller 

Bronze Ni.AL. 

Bronze Ni.AL. 

O-Ring 

Nitrile / NBR. 

Nitrile / NBR. 

Volute 

Cast Iron 

Bronze RG10 

Wear rings 

Bronze Ni.AL. 

Bronze Ni.AL. 

For some pump size can impeller i Stainless steel be an option  

 

 

 

 

 

Danpumps Pumps can be manufactured with other types of Mech. Seal and O-rings for specific conditions.

 

 

 

 

 

 

 

 

 

Содержание S-IP














Отзывы: