Dannmar D-12 Series Скачать руководство пользователя страница 36

GENERAL DISCLAIMER

In addition to all claim s listed on each of the following individual W ARRANTY pages, the following GENERAL
DISCLAIMERS apply.

1.

The purchaser of any DANNMAR product (Buyer) assum es the risk of verifying all m aterials or
resources used or relied on.  In no event will DANNMAR be liable to the Buyer or to anyone else for any
decision m ade or action taken in reliance on inform ation obtained from  any DANNMAR website or from  any
DANNMAR dealer, or third-party website, or any online or published catalog.

2.

DANNMAR has exclusive title and ownership rights including all intellectual property right throughout the world
for all m aterial and content contained on any DANNMAR website or from  any DANNMAR online or published
catalog.

3.

DANNMAR warrants that all products shown on any DANNMAR website or in any online or published catalog
conform  to DANNMAR published specifications only and are free from  defects in m aterial or workm anship as
m ore fully set forth in the W arranty for the specific product.

4.

DANNMAR websites m ay contain hypertext or other links to websites not owned or controlled by DANNMAR.
Links to other com puter system s or websites are not supervised nor regularly reviewed by DANNMAR.
DANNMAR specifically disavows legal responsibility for any inform ation, personal opinions, guidance, advice
or instruction that a Buyer receives from  others or other websites.

5.

Materials, design, specifications, im ages and other content from  any DANNMAR website, or any other
DANNMAR affiliate or dealer website, or any DANNMAR online or published catalog are subject to change.
DANNMAR takes no responsibility for im proper use or any results therof.  DANNMAR reserves the right to
m ake changes to all published warranties, website content, or published content without incurring any
obligation to notify the Buyer or public that changes were m ade.

6.

DANNMAR products are provided and sold as is without any express or im plied warranties including
warranties of m erchantability or fitness for particular purpose, other than the published written lim ited W arranty
for the specific product or as required by law.

7.

DANNMAR m akes no prom ises, guarantees or assurances that our products m eet any state, county, federal
or international m andated perm it, license, code, standard, certification, or any other m andate other than what
is listed or shown on DANNMAR website(s), or any DANNMAR online or published catalog.  Not all
DANNMAR lift m odels m eet the standards as prescribed by ANSI/ALI ALCTV-(current edition) or ANSI/UL
201.  Consult 

www.autolift.org

 for a com plete list of lift m odels that m eet ANSI/ALI ALCTV-(current edition) or

ANSI/UL 201, or contact DANNMAR vi

a              contact@dannmar.com.

 

                            

Buyer assum es full

responsibility for any state, county, federal or international m andated perm it, license, code, standard,
certification, or any other m andate required related to the installation and/or operation at any DANNMAR
product.  DANNMAR will not be responsible for any charges, fines, liens, or other levies im posed on the Buyer
related to any special or regional structural, seism ic or any other building code and/or codes such as the
Uniform  Building Code (UBC), International Building Code (IBC) or any other state, county, federal or
international m andated perm it, license, code, standard, certification, or other m andate, law, rule, regulation or
directive by any other agency, governm ent, adm inistrations, or corporations whether state, county, federal, or
international m andated.

8.

In no event will DANNMAR be liable for any special, incidental, or consequential dam ages based on breach of
warrant, breach of contract, negligence, strict tort, or any other legal theory.  Dam ages that DANNMAR will not
be responsible for include, but are not lim ited to: loss of profits; loss of savings or revenue; loss of use of the
product or any associated equipm ent; cost of capital; cost of any substitute equipm ent, facilities, or services;
downtim e; the claim s of third parties, including custom ers; and injury to property.  This lim itation does not
apply to dam ages caused by breach of the warranty of title and against infringem ents or to claim s for personal
injury.

9.

Unless m odified in a writing signed by both parties, it is understood that DANNMAR published W arranties and

36

Содержание D-12 Series









































Отзывы: