Daniels P25 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 56

background image

UG-001 Daniels P25 Radio Systems
www.danelec.com

Chapter 6: Radio System Components

36

User

Guide

S U B R A C K

The SR-39-1 subrack is designed to hold and interconnect the MT-4 series of P25 receiver, transmitter
and control modules on one universal motherboard. The subrack has room for two transmitter and
receiver pairs. The left side connectors are reserved for transmitter A and receiver A, while the right
side connectors are reserved for transmitter B and receiver B. See Figure 6-1.

Figure 6-1: Standard Subrack Conﬁ guration

If a VHF or UHF 30 Watt power ampliﬁ er is installed, only one transmitter and receiver pair can be
installed. The power ampliﬁ er takes up two slots as shown in Figure 6-2.

Figure 6-2: Standard Subrack with Power Ampliﬁ er

Power Input

The main power input (+10 to +17 Vdc; +13.8 Vdc nominal) connector is located on the back of the
subrack, on the motherboard. There is an ide9.5 Vdc power output connector on the motherboard
that is used to power other Daniels equipment at +9.5 Vdc (the CI-RC-4M controller for example). Do
not connect the main power input to the +9.5 Vdc power output connector, as a transient suppressor
(over voltage protection) will short to ground to protect the equipment.

Reverse voltage protection and over voltage protection (transient suppressor) is provided at the main
power input as well as the +9.5 Vdc line. The main power input is protected with a standard fast-blow
15 amp fuse. These components may require replacing if the power supply is not connected properly,
or even after a power surge or a lightning strike. The two transient suppressors have different voltage
ratings for the main power input and +9.5 Vdc lines. Figure 6-3 shows the subrack / motherboard rear
view.

SYSTEM

MONITOR

RECEIVER

B

TRANSMITTER

B

RECEIVER

A

TRANSMITTER

A

CONTROL

CARD

DANIELS

ELECTRONICS LTD.

DANIELS

ELECTRONICS LTD.

DANIELS

ELECTRONICS LTD.

DANIELS

ELECTRONICS LTD.

DANIELS

ELECTRONICS LTD.

POWER AMPLIFIER

A

SYSTEM

MONITOR

RECEIVER

A

TRANSMITTER

A

CONTROL

CARD

DANIELS

ELECTRONICS LTD.

DANIELS

ELECTRONICS LTD.

DANIELS

ELECTRONICS LTD.

DANIELS

ELECTRONICS LTD.

«
...
42
43
44
45
46
...
»

Содержание P25

























































Отзывы:

Нет отзывов

Похожие инструкции для P25

Бренд: Optex Страницы: 2

Бренд: Bestron Страницы: 24

Бренд: Datavideo Страницы: 12

Middleman EZM-100-50

Бренд: Easy Radiant Works Страницы: 28

Бренд: Frico Страницы: 14

Бренд: Zibro Страницы: 15

Бренд: Living & Co Страницы: 8

MASTER MH-135T-KFA

Бренд: Pinnacle International Страницы: 16

Бренд: Rowenta Страницы: 20

Eyecatchers heatwave extralarge

Бренд: Jaga Страницы: 10

Бренд: Fantech Страницы: 4

Бренд: TC Electronic Страницы: 5

Бренд: Sunbeam Страницы: 10

Бренд: Daewoo Страницы: 12

Бренд: VONROC Страницы: 84

Бренд: Dimplex Страницы: 2

Бренд: Dimplex Страницы: 3

Бренд: Dimplex Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды