Daniels Electronics MT-3 Series Скачать руководство пользователя страница 9

Страница: 9 / 9

DANIELS

ELECTRONICS LTD.

TN100 System Installation and Troubleshooting

MT-3 Radio Systems

5.0

Audio Control Cards

5.1

Deviation Between Receiver and Transmitter are Incorrect

1. Check the receiver output level using the extender card and note the impedance, either 600

or 5 K

(refer to the MT-3 Application Specific Manual).

2. Check the transmitter input level using the extender card, and note the impedance, either 600

5 K

3. Reset the audio level on the audio control card for the desired system deviation operation.

5.2

CTCSS Operation Incorrect

1. Check that the front panel switch is in the 'ON' position for CTCSS operation.

2. Encode / decode module can be selected for encode only, decode only or both. Check that the desired
operation is selected (refer to the MT-3 Application Specific Manual).

3. The encode / decode frequency may be wrong. Use the DIP switches to select the correct frequency
for encoding and decoding the same tone. To encode a tone different from the decoder a separate CTCSS
module is used. Set this low current module using solder jumpers.

4. If a sub-audible tone appears on the repeat audio path check that the subtone filter on the audio con-
trol card is enabled or the receiver has its optional sub-tone filter installed.

Operational Troubleshooting

Page 9 of 9

43 Erie Street

Toll Free

Canada & U.S.A.

International

Internet

Victoria, B.C.

Phone:

1-800-664-4066

Phone:

250-382-8268

e-mail:

[email protected]

Canada V8V 1P8

Fax:

1-877-750-0004

Fax:

250-382-6139

web:

www.danelec.com

TECHNICAL NOTES

TN100 Rev 3-0-0 Sep 08

iiss

rroo

iiss

ttii

iiss

lloo

ffaa

ttuu

rree

iiee

llss

llee

ttrr

iicc

ttdd

Содержание MT-3 Series










Результаты поиска

Содержание MT-3 Series

Отзывы:

Похожие инструкции для MT-3 Series

Бренды по названию

Популярные бренды

Daniels Electronics MT-3 Series, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание MT-3 Series

Отзывы:

Похожие инструкции для MT-3 Series

Бренды по названию

Популярные бренды