background image

3

Important safety information

Your safety is of the utmost importance to us. Please
make sure that you read this instruction booklet

before

attempting to install or use the appliance. If you are
unsure of any of the information contained in this
booklet, please contact the retailer where you purchased
your unit from.

General Information

o

This appliance is designed for domestic household use.

o

IMPORTANT:

The adjacent furniture and all materials used in

the installation

must

be able to withstand a minimum

temperature of 85°C above the ambient temperature of the

room it is located in, whilst in use.

o

Certain types of vinyl or laminate kitchen furniture are

particularly

prone

to

heat

damage

or

discoloration

at

temperatures below the guidelines given above.

o

Any damage caused by the appliance being installed

in

contravention of this temperature limit,

will be the liability of

the owner.

o

Your

new

appliance

is

guaranteed

against

electrical

or

mechanical defects, subject to certain exclusions that are noted

in the Conditions Of Guarantee. The foregoing does not affect

your statutory rights.

o

You should not use this appliance to store items on or as a work

surface.

o

No modifications to the appliance are permitted.

o

You should not store or place flammable or highly flammable

liquids/materials on top of or near the appliance. Items made

from aluminium, plastic or plastic film should also be kept away

from the appliance, as they may fuse to the surface.

Содержание DAN90AGG



























Отзывы: