Danfoss VLT Micro Drive FC 51 Series Скачать руководство пользователя страница 49

Страница: 49 / 74

4.12 Parameter Group 15: Drive Information

Parameter group containing information on operating
data, hardware configuration, software version, etc.

15-00 Operating Time

Range:

Function:

0 days

[0-65535
days]

View how many days the frequency
converter has been powered up.
The value is saved at power off and
cannot be reset.

15-01 Running Hours

Range:

Function:

[0- 2147483647] View running hours of motor.

The value is saved at power off and can be
reset in

15-07 Reset Running Hours Counter

15-02 kWh Counter

Range:

Function:

0 [0-65535] View power consumption in kWh as a mean value

over one hour.
Reset counter in

15-06 Reset kWh Counter

15-03 Power Ups

Range:

Function:

0 [0-2147483647] View number of times frequency converter

has been powered up.
Counter cannot be reset.

15-04 Over Temps

Range:

Function:

0 [0-65535] View number of times frequency converter has

tripped due to over temperature.
Counter cannot be reset.

15-05 Over Volts

Range:

Function:

[0-65535] View number of times frequency converter has

tripped due to over voltage.
Counter cannot be reset.

15-06 Reset kWh Counter

Option:

Function:

[0]

Do Not Reset

Counter is not reset.

[1]

Reset Counter

Counter is reset.

15-07 Reset Running Hours Counter

Option:

Function:

[0]

Do Not Reset

Counter is not reset.

[1]

Reset Counter

Counter is reset.

4.12.1 15-3* Fault Log

This parameter group contains a fault log showing reasons
for the ten latest trips.

15-30 Fault Log: Error Code

Range:

Function:

0 [0-255] View error code and look it up in

VLT Micro Quick

Guide, MG02B

4.12.2 15-4* Drive Identification

Parameters containing read only information about the
hardware and software configuration of the frequency
converter.

15-40 FC Type

Option:

Function:

View FC type.

15-41 Power Section

Option:

Function:

View power section of frequency converter.

15-42 Voltage

Option:

Function:

View voltage of frequency converter.

15-43 Software Version

Option:

Function:

View software version of frequency converter.

15-46 Frequency Converter Ordering No

Option: Function:

View ordering number for re-ordering frequency
converter in its original configuration.

15-48 LCP ID No

Option:

Function:

View LCP ID number.

15-51 Frequency Converter Serial Number

Option:

Function:

View frequency converter serial number.

Parameter Descriptions

VLT

Micro Drive FC 51 Programming Guide

MG02C602 - VLT

is a registered Danfoss trademark

Содержание VLT Micro Drive FC 51 Series











































































Результаты поиска

Содержание VLT Micro Drive FC 51 Series

Отзывы:

Похожие инструкции для VLT Micro Drive FC 51 Series

Бренды по названию

Популярные бренды

Danfoss VLT Micro Drive FC 51 Series, Руководство по программированию

Результаты поиска

Содержание VLT Micro Drive FC 51 Series

Отзывы:

Похожие инструкции для VLT Micro Drive FC 51 Series

Бренды по названию

Популярные бренды