Danfoss VLT Inverter Scroll CDS 801, Руководство по эксплуатации

Страница: 45 / 56

Address Name Description
40308 THERMO_OUT_TRACKING_ERROR_PCT If the compressor is running in external speed % control mode
the tracking error is calculated
The Tracking error is the difference between actual compressor
speed % and external speed % command
If not running external speed, the tracking error is set to 0
40309 THERMO_OUT_POWER_PCT Actual Drive power in % of nominal power
40401 THERMO_SETUP_UNITTYPE Unit type:
0 = 3 Ton
1 = 4 Ton
2 = 5 Ton
40402 THERMO_SETUP_SYSTEM_CONFIGURATION System Configuration
1 = ID1 (not active)
2 = ID2 AC/HP reversible
3 = ID3 (not active)
4 = ID4 GSHP reversible
5 = ID5 (not active)
6 = ID6 AC only
40403 THERMO_SETUP_COMPRESSOR_MINIMUM_SPEED_HZ Minimum compressor speed
40404 THERMO_SETUP_COMPRESSOR_MAXIMUM_SPPED_HZ Maximum compressor speed
40405 THERMO_SETUP_DELTA_HZ_PER_SEC Allowed speed rate of change in Hz pr. s
40407 THERMO_SETUP_DELTA_TEMP Delta temperature setting for fan “Delta T” control mode
40409 THERMO_SETUP_OIL_LOSS_TRIG_TIME_SEC When running below oil return speed for more than this time,
oil return is initiated
40410 THERMO_SETUP_OIL_RETURN_SPEED_HZ Defined oil return speed
40411 THERMO_SETUP_OIL_RETURN_HOLD_TIME_SEC Hold time for running at oil return speed
40412 THERMO_SETUP_START_UP_SPEED_HZ Start up speed for system
40413 THERMO_SETUP_START_UP_HOLD_TIME_SEC Hold time for start up speed
40414 THERMO_SETUP_RESTART_TIME_SEC Minimum Time between repeated starts
40415 THERMO_SETUP_CANCEL_CENTER_HZ_1 Centre frequency #1 for speed range cancellation
40416 THERMO_SETUP_CANCEL_BANDWIDTH_HZ_1 Bandwidth #1 for speed range cancellation
40417 THERMO_SETUP_CANCEL_CENTER_HZ_2 Centre frequency #2 for speed range cancellation
40418 THERMO_SETUP_CANCEL_BANDWIDTH_HZ_2 Bandwidth #2for speed range cancellation
40419 THERMO_SETUP_CANCEL_CENTER_HZ_3 Centre frequency #3 for speed range cancellation
40420 THERMO_SETUP_CANCEL_BANDWIDTH_HZ_3 Bandwidth #3 for speed range cancellation
40421 THERMO_SETUP_CANCEL_CENTER_HZ_4 Centre frequency #4 for speed range cancellation
40422 THERMO_SETUP_CANCEL_BANDWIDTH_HZ_4 Bandwidth #4 for speed range cancellation
40423 THERMO_SETUP_CANCEL_CENTER_HZ_5 Centre frequency #5 for speed range cancellation
40424 THERMO_SETUP_CANCEL_BANDWIDTH_HZ_5 Bandwidth #5 for speed range cancellation
40425 THERMO_SETUP_PI_COMPRESSOR_AC_KP Proportional gain for AC compressor capacity controller
40427 THERMO_SETUP_PI_COMPRESSOR_AC_TN Integration time for AC compressor capacity controller
40428 THERMO_SETUP_PI_COMPRESSOR_AC_TT Tracking time constant for AC compressor capacity controller
40429 THERMO_SETUP_PI_COMPRESSOR_HP_KP Proportional gain for HP compressor capacity controller
40431 THERMO_SETUP_PI_COMPRESSOR_HP_TN Integration time for HP compressor capacity controller
40432 THERMO_SETUP_PI_COMPRESSOR_HP_TT Tracking time constant for HP compressor capacity controller
41609 OUTDOOR_FAN_CAPACITY_PCT_MIN Minimum duty cycle that will be output by the fan controller
41611 OUTDOOR_FAN_CAPACITY_PCT_MAX Maximum duty cycle that will be output by the fan controller
41613 OUTDOOR_FAN_CONTROL_SIGNAL_FREQUENCY Set frequency of the condenser fan PWM signal
40479 THERMO_SETUP_CRANK_CASE_HEATING_ON_TEMP Ambient temperature where crankcase heating is activated
Table 6.2 Thermo Controller Register Overview (Node 162)
Embedded Application Contro...
VLT
®
Inverter Scroll CDS 801 Operating Instructions
MG10V402 - VLT
®
is a registered Danfoss trademark 43
6 6